Electric Vehicle with Multi-Speed Transmission: A Review on Performances and Complexities

被引:43
作者
Ahssan, Md Ragib [1 ]
Ektesabi, Mehran Motamed [1 ]
Gorji, Saman Asghari [1 ]
机构
[1] Swinburne Univ Technol, Melbourne, Vic, Australia
关键词
Dynamic and economic performances; Electric vehicle; Gear ratio optimization; Multi-speed transmission; Shift scheduling strategy;
D O I
10.4271/08-07-02-0011
中图分类号
U [交通运输];
学科分类号
08 ; 0823 ;
摘要
Electric vehicles (EVs) with multi-speed transmission offer improved performances compared to those with single speed transmission system in terms of top speed, fast acceleration, or gradeability along with driving range. In this study, relevant literature is extensively analyzed to explore the performances and associated complexities with multi-speed automatic manual/mechanical transmission (AMT) system in EVs. In EV powertrain, the only torque generator component is electric motor, which is not equally efficient throughout wider speed range. To the other end, vehicles need to run at different speeds in diverse driving conditions. The study shows that multi-speed transmission system enables efficient operation of electric motor by choosing an appropriate gear at different driving torque-speed demands and thus contributes to achieve desired vehicle performances at minimum energy consumption. To demonstrate the differences, both dynamic and economic performances with multi-gear system and single speed system are compared, and the results of various techniques are presented in the form of tables and bar charts. A quantitative analysis is also conducted to show the performance improvement achievable by employing multi-speed transmission concept in EVs. Apart from additional mass, gear ratio selection and torque interruption during gear shifting are major obstacles to improve drivetrain efficiency and riding comfort in EVs with multi-speed transmission system. For optimal gear ratio in transmission system, genetic algorithm (GA) is found to be implemented in most articles. It is also observed that variable shift schedule needs to be considered during the optimization process to get the paramount gear ratios. Tables and bar charts are used to show the results of recent relevant works to these issues. In this article, the readers would gain a comprehensive knowledge on how multi-speed transmission technology can outperform the single speed system within EV platform and what the inherent challenges are.
引用
收藏
页码:169 / 181
页数:13
相关论文
共 53 条
  • [41] Comparative Research on the Transmission Form of the Electric Bus
    Wang, Wenwei
    Hou, Rui
    Yu, Quanqing
    Lin, Cheng
    [J]. CUE 2015 - APPLIED ENERGY SYMPOSIUM AND SUMMIT 2015: LOW CARBON CITIES AND URBAN ENERGY SYSTEMS, 2016, 88 : 928 - 934
  • [42] On the electrification of road transport - Learning rates and price forecasts for hybrid-electric and battery-electric vehicles
    Weiss, Martin
    Patel, Martin K.
    Junginger, Martin
    Perujo, Adolfo
    Bonnel, Pierre
    van Grootveld, Geert
    [J]. ENERGY POLICY, 2012, 48 : 374 - 393
  • [43] Comprehensive drive train efficiency analysis of hybrid electric and fuel cell vehicles based on motor-controller efficiency modeling
    Williamson, Sheldon S.
    Lukic, Srdjan M.
    Emadi, Ali
    [J]. IEEE TRANSACTIONS ON POWER ELECTRONICS, 2006, 21 (03) : 730 - 740
  • [44] Powertrain architectures of electrified vehicles: Review, classification and comparison
    Wu, Guang
    Zhang, Xing
    Dong, Zuomin
    [J]. JOURNAL OF THE FRANKLIN INSTITUTE-ENGINEERING AND APPLIED MATHEMATICS, 2015, 352 (02): : 425 - 448
  • [45] Wyczalek F. A., 1999, 1999012707 SAE, DOI [10.4271/1999-01-2707, DOI 10.4271/1999-01-2707]
  • [46] Yin Q., 2014, TRANSP EL AS PAC ITE, P1, DOI [10.1109/ITEC-AP.2014.6940949, DOI 10.1109/ITEC-AP.2014.6940949]
  • [47] Yu CH, 2012, IEEE ASME INT C ADV, P971, DOI 10.1109/AIM.2012.6266016
  • [48] THREE-SPEED TRANSMISSION SYSTEM FOR PURELY ELECTRIC VEHICLES
    Zhang, Z.
    Zuo, C.
    Hao, W.
    Zuo, Y.
    Zhao, X. L.
    Zhang, M.
    [J]. INTERNATIONAL JOURNAL OF AUTOMOTIVE TECHNOLOGY, 2013, 14 (05) : 773 - 778
  • [49] Zhou X., 2013, 2013011477 SAE, DOI [10.4271/2013-01-1477, DOI 10.4271/2013-01-1477]
  • [50] Zhou XX, 2013, INTERNATIONAL MECHANICAL ENGINEERING CONGRESS AND EXPOSITION - 2012, VOL 3, PTS A-C: DESIGN, MATERIALS, AND MANUFACTURING, P289