CIRCULATORY HIGH-VISCOSITY NON-NEWTONIAN FLUID FLOW IN A SINGLE-SCREW EXTRUDER CHANNEL

被引：1

作者：

Ponomareva, M. A. ^{[1
,2
]}

Filina, M. P. ^{[2
]}

Yakutenok, V. A. ^{[2
]}

机构：

[1] Tomsk State Univ, Phys & Math, Tomsk, Russia

[2] Tomsk State Univ, Tomsk, Russia

来源：

VESTNIK TOMSKOGO GOSUDARSTVENNOGO UNIVERSITETA-MATEMATIKA I MEKHANIKA-TOMSK STATE UNIVERSITY JOURNAL OF MATHEMATICS AND MECHANICS | 2016年 / 02期

关键词：

single-screw extruder; non-Newtonian fluid; Indirect Boundary Element Method; flow in lid-driven cavity;

D O I：

10.17223/19988621/40/10

中图分类号：

O3 [力学];

学科分类号：

08 ; 0801 ;

摘要：

This paper is devoted to definition of a width-to-depth ratio of a single-screw extruder channel when sidewalls do not affect the velocity profiles of circulatory high-viscosity non-Newtonian fluid flow at the mid of the channel. The channel has a rectangular cross-section. Power-law model is used to describe fluid behavior. The indirect boundary element method is used for numerical solution taking into account of sidewalls. Comparing of obtained velocity profiles with the known results showed a good agreement. Research is performed in the range of power-law index from 0.4 to 1.0. The method for obtaining the velocity component profiles for the case of shear-thinning fluid flow without considering influence of sidewalls is presented. The width-to-depth ratio of a single-screw extruder channel when it is acceptable to neglect influence of sidewalls on flow at the mid of the channel is defined.

引用

页码：97 / 107

页数：11

共 50 条

[41] FLOW OF A POWER-LAW FLUID IN A MELT-FED SINGLE-SCREW EXTRUDER
POON, SY
JOURNAL OF FLUIDS ENGINEERING-TRANSACTIONS OF THE ASME, 1973, 95 (01): : 81 - 90
[42] Reversal of flow of a non-Newtonian fluid in an expanding channel
Harley, C.
Momoniat, E.
Rajagopal, K. R.
INTERNATIONAL JOURNAL OF NON-LINEAR MECHANICS, 2018, 101 : 44 - 55
[43] Flow reversals of a non-Newtonian fluid in an expanding channel
Herbst, R. S.
Harley, C.
Rajagopal, K. R.
INTERNATIONAL JOURNAL OF NON-LINEAR MECHANICS, 2023, 154
[44] Study of newtonian and non-Newtonian fluid flow in a channel with a moving indentation
Neofitou, P
Drikakis, D
Leschziner, MA
CARDIOVASCULAR FLOW MODELLING AND MEASUREMENT WITH APPLICATION TO CLINICAL MEDICINE, 1999, 70 : 39 - 47
[45] Numerical flow simulation for bingham plastics in a single-screw extruder
Bohme, G
Broszeit, J
THEORETICAL AND COMPUTATIONAL FLUID DYNAMICS, 1997, 9 (01) : 65 - 74
[46] Numerical Flow Simulation for Bingham Plastics in a Single-Screw Extruder
G. Böhme
J. Broszeit
Theoretical and Computational Fluid Dynamics, 1997, 9 : 65 - 74
[47] ANALYSIS OF STEADY NON-ISOTHERMAL FLOW OF POLYMER MELTS IN A SINGLE-SCREW EXTRUDER
Khametova, M. G.
CHEMICAL AND PETROLEUM ENGINEERING, 2012, 48 (7-8) : 488 - 493
[48] Distributive mixing in a single-screw extruder - Evaluation in the flow direction
Rwei, SP
POLYMER ENGINEERING AND SCIENCE, 2001, 41 (10): : 1665 - 1673
[49] Flow of a non-Newtonian fluid
V. G. Pridanov
V. I. Khonichev
Technical Physics, 2012, 57 : 1475 - 1478
[50] FLOW OF NON-NEWTONIAN FLUID
THIRIET, M
MARTINBORRET, G
HECHT, F
ARCHIVES OF PHYSIOLOGY AND BIOCHEMISTRY, 1995, 103 (03) : C151 - C151

← 1 2 3 4 5 →