GAMMA-PHASE IN INJECTION-MOLDED ISOTACTIC POLYPROPYLENE

被引：24
|
作者：
KALAY, G
ALLAN, P
BEVIS, MJ
机构：
[1] Wolfson Centre for Materials Processing, Department of Materials Technology, Brunel University, Uxbridge
来源：
POLYMER | 1994年 / 35卷 / 12期
关键词：
POLYPROPYLENE; MOLECULAR ORIENTATION; CRYSTALLINITY;
D O I：
10.1016/0032-3861(94)90366-2
中图分类号：
O63 [高分子化学（高聚物）];
学科分类号：
070305 ; 080501 ; 081704 ;
摘要：
Wide angle X-ray diffraction has been used to investigate polymorphism in isotactic polypropylene (IPP) mouldings produced by conventional injection moulding and by shear controlled orientation injection moulding (SCORIM). Gamma Phase was found to form in highly oriented IPP produced by SCORIM, with a marked enhancement of the preferred orientation of the alpha phase and percentage crystallinity when compared with conventionally moulded IPP.
引用
收藏
页码：2480 / 2482
页数：3
相关论文
共 50 条
  • [21] Changes of microstructure and mechanical properties of injection-molded polypropylene sheets by rolling process
    Qiu, JH
    Kawagoe, M
    Mizuno, W
    Morita, M
    Miyaji, T
    KOBUNSHI RONBUNSHU, 1997, 54 (11) : 778 - 784
  • [22] Effects of hot roll process on the morphology and tensile properties of injection-molded polypropylene
    Qiu, JH
    KOBUNSHI RONBUNSHU, 2006, 63 (06) : 397 - 403
  • [23] Influence of nucleating agents on morphology and properties of injection-molded polypropylene
    Abreu, Andressa Argani
    Talabi, Segun Isaac
    Lucas, Alessandra de Almeida
    POLYMERS FOR ADVANCED TECHNOLOGIES, 2021, 32 (05) : 2197 - 2206
  • [24] Development of β and α isotactic polypropylene polymorphs in injection molded structural foams
    Djoumaliisky, Strashimir
    Luisa Cerrada, Maria
    Dobreva, Tatyana
    Zipper, Peter
    CHEMICAL PAPERS, 2010, 64 (02) : 246 - 254
  • [25] MEASUREMENT OF MOLECULAR ORIENTATION IN INJECTION-MOLDED POLYPROPYLENE BY MICRO-RAMAN SPECTROSCOPY
    Akashige, Etsushi
    Usami, Takao
    ANALYTICAL SCIENCES, 1991, 7 : 1655 - 1656
  • [26] Morphology of Injection-Molded Isotactic Polypropylene/Silica Composites Prepared via in-Situ Sol-Gel Technology
    Zhu, Xiaomin
    Melian, Claudiu
    Dou, Qizheng
    Peter, Karin
    Demco, Dan E.
    Moller, Martin
    Anokhin, Denis V.
    Le Meins, Jean-Marc
    Ivanov, Dimitri A.
    MACROMOLECULES, 2010, 43 (14) : 6067 - 6074
  • [27] Development of β and α isotactic polypropylene polymorphs in injection molded structural foams
    Strashimir Djoumaliisky
    Maria Luisa Cerrada
    Tatyana Dobreva
    Peter Zipper
    Chemical Papers, 2010, 64 : 246 - 254
  • [28] Structure and mechanical anisotropy of injection-molded polypropylene with a plywood structure
    Panitha Phulkerd
    Soichiro Hirayama
    Shogo Nobukawa
    Takahiro Inoue
    Masayuki Yamaguchi
    Polymer Journal, 2014, 46 : 226 - 233
  • [29] Orientation and Epitaxy in the Injection-Molded Bars of Linear Low-Density Polyethylene/Isotactic Polypropylene Blends: An Infrared Dichroism Measurement
    Su, Run
    Wang, Ke
    Zhang, Qin
    Chen, Feng
    Fu, Qiang
    Xu, Wenfei
    Na, Bing
    JOURNAL OF PHYSICAL CHEMISTRY B, 2009, 113 (21) : 7423 - 7429
  • [30] Isotactic polypropylene/ethylene-co-propylene blends:: Influence of the copolymer microstructure on rheology, morphology, and properties of injection-molded samples
    D'Orazio, L
    Mancarella, C
    Martuscelli, E
    Sticotti, G
    Cecchin, G
    JOURNAL OF APPLIED POLYMER SCIENCE, 1999, 72 (05) : 701 - 719
12345