Microstructures in Friction Stir Welded 304 Austenitic Stainless Steel

被引：1
|
作者：
H. Kokawa
S. H. C. Park
Y. S. Sato
K. Okamoto
S. Hirano
M. Inagaki
机构：
[1] Tohoku University,Department of Materials Processing, Graduate School of Engineering
[2] Hitachi Ltd.,Hitachi Research Laboratory
来源：
Welding in the World | 2005年 / 49卷 / 3-4期
关键词：
Friction stir welding; Friction welding; Stainless steels; Steels; Microstructure; Grain size; Hardness; Mechanical properties; Austenite; Ferrite; Recrystallisation; Reference lists;
D O I：
10.1007/BF03266473
中图分类号：
学科分类号：
摘要：
Friction stir welding was applied to 304 austenitic stainless steel. The microstructural evolution and hardness distribution in the weld were investigated. The stir zone (SZ) and thermomechanically affected zone (TMAZ) showed dynamically recrystallised and recovered microstructures, respectively. The hardness of the SZ was higher than that of the base material and the maximum hardness was located in the TMAZ. The higher hardness in TMAZ was attributed to high density of dislocations and sub-grains. Electron microscopic observations revealed that ferrite and sigma phase were formed in austenite matrix in the SZ depending on the cooling rate during FSW.
引用
收藏
页码：34 / 40
页数：6
相关论文
共 50 条
  • [21] Microstructure and mechanical properties of dissimilar friction stir welded type 304 austenitic stainless steel to Q235 low carbon steel
    Wang, Hongduo
    Wang, Kuaishe
    Wang, Wen
    Huang, Liying
    Peng, Pai
    Yu, Hailiang
    MATERIALS CHARACTERIZATION, 2019, 155
  • [22] Influence of welding speed on microstructure formation in friction-stir-welded 304 austenitic stainless steels
    Mohsen Hajizadeh
    Sajjad Emami
    Tohid Saeid
    International Journal of Minerals, Metallurgy and Materials, 2020, 27 : 1517 - 1524
  • [23] Influence of welding speed on microstructure formation in friction-stir-welded 304 austenitic stainless steels
    Hajizadeh, Mohsen
    Emami, Sajjad
    Saeid, Tohid
    INTERNATIONAL JOURNAL OF MINERALS METALLURGY AND MATERIALS, 2020, 27 (11) : 1517 - 1524
  • [24] Influence of welding speed on microstructure formation in friction-stir-welded 304 austenitic stainless steels
    Mohsen Hajizadeh
    Sajjad Emami
    Tohid Saeid
    International Journal of Minerals Metallurgy and Materials, 2020, 27 (11) : 1517 - 1524
  • [25] Joint properties of friction stir welded austenitic stainless steels
    Tokyu Car Corporation
    不详
    Yosetsu Gakkai Ronbunshu, 2006, 2 (174-180):
  • [26] High Quality-High Speed Friction Stir Welding of 304 Austenitic Stainless Steel
    Ishikawa, Takeshi
    Fujii, Hidetoshi
    Genchi, Kazuo
    Iwaki, Shunichi
    Matsuoka, Shigeki
    Nogi, Kiyoshi
    TETSU TO HAGANE-JOURNAL OF THE IRON AND STEEL INSTITUTE OF JAPAN, 2008, 94 (11): : 539 - 544
  • [27] Effect of post-welded heat treatment on the microstructures and mechanical properties of friction stir welded joint of high-nitrogen austenitic stainless steel
    State Key Laboratory of Metastable Materials Science and Technology, Yanshan University, Qinhuangdao
    066004, China
    不详
    066004, China
    Jixie Gongcheng Xuebao, 22 (47-53):
  • [28] Mechanical Properties and Microstructural Characterization of Friction Stir Welded AISI 316 Austenitic Stainless Steel
    Meshram, Manish P.
    Kodli, Basanth Kumar
    Dey, Suhash R.
    INTERNATIONAL CONFERENCE ON ADVANCES IN MANUFACTURING AND MATERIALS ENGINEERING (ICAMME 2014), 2014, 5 : 2376 - 2381
  • [29] Texture analyses of friction stir welded austenitic stainless steel AISI-316L
    Meshram, Manish P.
    Tamboli, Rameez R.
    Kodli, Basanth K.
    Yebaji, Sushil G.
    Dey, Suhash R.
    ADVANCES IN MATERIALS AND PROCESSING TECHNOLOGIES, 2018, 4 (02) : 244 - 254
  • [30] Stress corrosion cracking failure of friction stir welded nuclear grade austenitic stainless steel
    Rajasekaran, R.
    Lakshminarayanan, A. K.
    Damodaram, R.
    Balasubramanian, V.
    ENGINEERING FAILURE ANALYSIS, 2021, 120
12345