Development and Modeling of Welding Differentially Heat-Strengthened Railway Rails. Laboratory Studies

被引：0
|
作者：
Kozyrev N.A. [1 ]
Shevchenko R.A. [1 ]
Usol’tsev A.A. [1 ]
Prudnikov A.N. [1 ]
机构：
[1] Siberian State Industrial University, Novokuznetsk, 654007, Kemerovo oblast
来源：
Steel in Translation | 2020年 / 50卷 / 07期
基金：
俄罗斯基础研究基金会;
关键词：
current; hardness; heat treatment; heat-affected zone; pulse; rails; resistance welding; welding mode;
D O I：
10.3103/S0967091220070086
中图分类号：
学科分类号：
摘要：
Abstract: In this paper, we study the effect of welding modes with subsequent isothermal exposure on the quality parameters of the welded joint under laboratory conditions using rail steel samples. Welding of the samples was performed by passing pulses of alternating electric current after welding. Welding was carried out using an MS-2008M resistance butt welding machine with several changes in the control actions. Chromel–alumel thermocouples were used to measure the metal temperature in the heat-affected zone (HAZ). The collection and processing of data from thermocouples was performed using the “Tempol” measuring complex. The temperature of the metal of the welded seam (where it is not possible to install a thermocouple) was measured using a HotFind-D thermal imager. Experimental results and physical and mechanical properties of samples: hardness HB, HAZ length, yield strength, ultimate strength, relative elongation, relative narrowing, and presence of non-metallic inclusions in weld metal are presented. The calculation of hardness deviations (decrease–increase, total deviation) on the surface of the welded joint of the samples was carried out in relation to the requirements established by GOST R 51685–2013. A resistance butt welding method that allows obtaining a welded joint of products from rail steel with a uniform distribution of hardness and a small HAZ is proposed. The dependence of microhardness on the volume fraction of structural components was determined. The effect of the parameters of pulse contact post-weld heating on the decrease in the hardness of the welded joint metal relative to the hardness of the base metal and on the length of the HAZ are modeled. The proposed method allows regulating the metal structure of the welded joint of the rails without resorting to additional local heat treatment. © 2020, Allerton Press, Inc.
引用
收藏
页码：438 / 444
页数：6
相关论文
共 11 条
  • [1] Development and Modeling of the Technological Welding Process of Differentially Heat-Strengthened Rails: Industrial Testing
    Kozyrev N.A.
    Shevchenko R.A.
    Usol’tsev A.A.
    Prudnikov A.N.
    Bashchenko L.P.
    Steel in Translation, 2020, 50 (05) : 289 - 295
  • [2] Development and Modeling of Differentially Heat-Strengthened Rail Welding: Welding and Local Heat Treatment Modeling
    Kozyrev N.A.
    Shevchenko R.A.
    Usol’tsev A.A.
    Prudnikov A.N.
    Bashchenko L.P.
    Steel in Translation, 2020, 50 (03) : 139 - 145
  • [3] On the Question of Monitoring Residual Stresses in Selectively Heat-Strengthened Rails
    V. V. Murav’ev
    K. A. Tapkov
    S. V. Len’kov
    Russian Journal of Nondestructive Testing, 2018, 54 : 675 - 681
  • [4] On the Question of Monitoring Residual Stresses in Selectively Heat-Strengthened Rails
    Murav'ev, V. V.
    Tapkov, K. A.
    Len'kov, S. V.
    RUSSIAN JOURNAL OF NONDESTRUCTIVE TESTING, 2018, 54 (10) : 675 - 681
  • [5] Achievement of equal wear resistant of the heat-strengthened switch point and frame rails
    Rufanov, U.G.
    Fedorchenko, I.N.
    Krasheninnikova, O.A.
    Lutsenko, V.L.
    Tkalich, G.A.
    Metallurgicheskaya i Gornorudnaya Promyshlennost, 2002, (04): : 49 - 51
  • [6] Limiting Factors for Choice and Development of Steels for Railway Wheels and Rails.
    Masin, Alois
    Hutnicke listy, 1984, 39 (08): : 552 - 559
  • [7] DEVELOPMENT AND INDUSTRIAL ASSIMILATION OF IMPROVED TECHNOLOGY FOR THERMAL HARDENING OF RAILWAY RAILS.
    Vinokurov, I.Ya.
    Lashchenko, L.B.
    Murav'ev, E.A.
    Nikonova, N.N.
    Safonova, K.E.
    Shur, E.A.
    Metal Science and Heat Treatment (English Translation of Metallovedenie i Termicheskaya Obrabotka, 1984, 26 (9-10): : 753 - 757
  • [8] DEVELOPMENT OF FLASH BUTT AND GAS PRESSURE WELDING FOR HIGH-STRENGTH RAILS.
    Okazaki, Atsushi
    Kageyama, Hideaki
    Sugino, Kazuo
    Masumoto, Hiroki
    1600,
  • [9] The Microstructure of Differentially Heat Strengthened Railroad Rails Manufactured by the EVRAZ ZSMK Company
    A. A. Umanskii
    A. V. Golovatenko
    A. S. Simachev
    L. V. Dumova
    Metal Science and Heat Treatment, 2022, 64 : 343 - 349
  • [10] The Microstructure of Differentially Heat Strengthened Railroad Rails Manufactured by the EVRAZ ZSMK Company
    Umanskii, A. A.
    Golovatenko, A. V.
    Simachev, A. S.
    Dumova, L. V.
    METAL SCIENCE AND HEAT TREATMENT, 2022, 64 (5-6) : 343 - 349
12