Tribological and surface morphological characteristics of titanium alloys: a review

被引：54

作者：

Gupta, Munish Kumar ^{[1
]}

El Etri, Hamza ^{[2
]}

Korkmaz, Mehmet Erdi ^{[2
]}

Ross, Nimel Sworna ^{[3
]}

Krolczyk, Grzegorz M. ^{[1
]}

Gawlik, Jozef ^{[4
]}

Yasar, Nafiz ^{[5
]}

Pimenov, Danil Yu ^{[6
]}

机构：

[1] Opole Univ Technol, Fac Mech Engn, 76 Proszkowska St, PL-45758 Opole, Poland

[2] Karabuk Univ, Dept Mech Engn, Karabuk, Turkey

[3] Kings Engn Coll, Dept Mech Engn, Irungattukottai, Tamil Nadu, India

[4] Cracow Univ Technol, Fac Mech Engn, Al Jana Pawla 2 37, PL-31864 Krakow, Poland

[5] Karabuk Univ, Venice Vocat High Sch, Karabuk, Turkey

[6] South Ural State Univ, Dept Automated Mech Engn, Lenin Prosp 76, Chelyabinsk 454080, Russia

来源：

ARCHIVES OF CIVIL AND MECHANICAL ENGINEERING | 2022年 / 22卷 / 02期

关键词：

Titanium; Tribological behavior; Surface morphology; Dry sliding; Lubricated sliding; DRY SLIDING WEAR; METAL-MATRIX COMPOSITES; TI-6AL-4V ALLOY; MECHANICAL-PROPERTIES; RESIDUAL-STRESSES; ACOUSTIC-EMISSION; TUNGSTEN CARBIDE; HIGH-TEMPERATURE; INCONEL; 718; TOOL WEAR;

D O I：

10.1007/s43452-022-00392-x

中图分类号：

TU [建筑科学];

学科分类号：

0813 ;

摘要：

Being easily fabricated, welded, biocompatible, having a high strength-to-weight ratio, withstanding comparatively high temperatures up to 800 degrees C and low modulus of elasticity make grade titanium and its alloys an important choice for automotive, biomedical and aerospace industries. In contempt of the different pleasant assets of Ti-6Al-4V alloy, the operation of this alloy is restricted especially when it comes to tribological and surface morphological characteristics. Enhancing these properties is important, for this purpose, a diversity of attempts and studies have been conducted. This paper mounts a review of morphological and tribological behaviors of titanium alloys including Ti-6Al-4V against different materials counting with carbide tools and other types of materials under dry and lubricated sliding conditions. The surface morphological, wear, and other properties have been discussed in this review article.

引用

页数：23

共 110 条

[51]

Krolczyk G., 2016, NAT RESOUR ENG, V1, P51, DOI [10.1080/23802693.2016.1246278, DOI 10.1080/23802693.2016.1246278]

[52] Determination of tool life and research wear during duplex stainless steel turning [J].

Krolczyk, G. M. ;

Nieslony, P. ;

Legutko, S. .

ARCHIVES OF CIVIL AND MECHANICAL ENGINEERING, 2015, 15 (02) :347-354

[53] ANOVA and fuzzy rule based evaluation and estimation of flank wear, temperature and acoustic emission in turning [J].

Kuntoglu, Mustafa ;

Saglam, Haci .

CIRP JOURNAL OF MANUFACTURING SCIENCE AND TECHNOLOGY, 2021, 35 :589-603

[54] Investigation of signal behaviors for sensor fusion with tool condition monitoring system in turning [J].

Kuntoglu, Mustafa ;

Saglam, Haci .

MEASUREMENT, 2021, 173

[55] Investigation of progressive tool wear for determining of optimized machining parameters in turning [J].

Kuntoglu, Mustafa ;

Saglam, Haci .

MEASUREMENT, 2019, 140 :427-436

[56]

Lepicka M, 2016, REV ADV MATER SCI, V46, P86

[57] Physic-chemical analysis for high-temperature tribology of WC-6Co against Ti-6Al-4V by pin-on-disc method [J].

Liang, Xiaoliang ;

Liu, Zhanqiang ;

Wang, Bing .

TRIBOLOGY INTERNATIONAL, 2020, 146

[58]

Liu Y, 2006, SPACE TECHNOL PROC, V6, P309

[59] The surface characterization of microporous titanium carbide coating on titanium alloys [J].

Luo, Yong ;

Chai, Wei ;

Yang, Li ;

Tian, Maocai ;

Xu, Hao ;

Chen, Wenwen .

PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART J-JOURNAL OF ENGINEERING TRIBOLOGY, 2014, 228 (05) :521-528

[60] Influence of Bio-Lubricants on the Tribological Properties of Ti6Al4V Alloy [J].

Luo, Yong ;

Yang, Li ;

Tian, Maocai .

JOURNAL OF BIONIC ENGINEERING, 2013, 10 (01) :84-89

← 1 2 3 4 5 6 7 8 9 10 →