Effect of machining area on material removal rate in strip EDM

被引：0
|
作者：
Ki Young Song
Chong Nam Chu
机构：
[1] Sharp Engineering,Department of Mechanical and Aerospace Engineering
[2] Seoul National University,undefined
来源：
International Journal of Precision Engineering and Manufacturing | 2015年 / 16卷
关键词：
Electrical discharge machining; Electrode; Wear;
D O I：
暂无
中图分类号：
学科分类号：
摘要：
Strip EDM is similar to wire EDM, except that the electrode is a roll of brass strip. In this study, investigated is the effect of machining area on material removal rate (MRR) in strip EDM, The MRR was measured according to different machining areas and different electrical discharge conditions. For a given discharge condition, optimal machining area for maximum MRR was identified. The optimal machining area was larger under higher discharge energy condition. It is shown that strip EDM is much more efficient than wire EDM because material removal rate is much higher and the electrode consumption is much less.
引用
收藏
页码：2435 / 2440
页数：5
相关论文
共 50 条
  • [21] Modelling effect of magnetic field on material removal in dry electrical discharge machining
    Abhishek GUPTA
    Suhas S JOSHI
    Plasma Science and Technology, 2017, (02) : 83 - 92
  • [22] Simulation and experimental research of material removal rate in micro-electrochemical discharge machining process
    Kumar, Manoj
    Vaishya, R. O.
    Suri, N. M.
    ADVANCES IN MATERIALS AND PROCESSING TECHNOLOGIES, 2024, 10 (02) : 867 - 882
  • [23] Modelling of material removal rate in the magnetic field and air-assisted electrical discharge machining
    Beravala, Hardik
    Pandey, Pulak M.
    PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART C-JOURNAL OF MECHANICAL ENGINEERING SCIENCE, 2020, 234 (07) : 1286 - 1297
  • [24] Investigation of the spark cycle on material removal rate in wire electrical discharge machining of advanced materials
    Miller, SF
    Shih, AJ
    Qu, J
    INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE, 2004, 44 (04): : 391 - 400
  • [25] Material removal mechanisms by EDM of zirconia reinforced MWCNT nanocomposites
    Melk, Latifa
    Antti, Marta-Lena
    Anglada, Marc
    CERAMICS INTERNATIONAL, 2016, 42 (05) : 5792 - 5801
  • [26] An investigation of mechanical properties and material removal rate, tool wear rate in EDM machining process of AL2618 alloy reinforced with Si3N4, AlN and ZrB2 composites
    Kumar, N. Mathan
    Kumaran, S. Senthil
    Kumaraswamidhas, L. A.
    JOURNAL OF ALLOYS AND COMPOUNDS, 2015, 650 : 318 - 327
  • [27] Effects of Non-Electrical Parameters on Material Removal Rate of High-Speed Small Hole EDM Drilling
    Cao, M. R.
    Wang, Y. Q.
    Yang, S. C.
    Yang, S. Q.
    Li, W. H.
    SURFACE FINISHING TECHNOLOGY AND SURFACE ENGINEERING, 2008, 53-54 : 403 - 407
  • [28] Investigations on material removal rate of reduced graphene oxide coated copper electrodes for electric discharge machining
    Patil, Suraj
    Patil, Maharudra
    Kulkarni, Raviraj
    Malik, Vinayak
    ADVANCES IN MATERIALS AND PROCESSING TECHNOLOGIES, 2024, 10 (04) : 2741 - 2760
  • [29] Experimental investigation into material removal mechanisms in High Speed Wire EDM
    Osswald, Kai
    Brandl, Lukas
    Lochmahr, Ingo
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2020, 111 (7-8): : 2163 - 2170
  • [30] Experimental investigation into material removal mechanisms in High Speed Wire EDM
    Kai Oßwald
    Lukas Brandl
    Ingo Lochmahr
    The International Journal of Advanced Manufacturing Technology, 2020, 111 : 2163 - 2170
12345