Aging kinetics and mechanical properties of copper-bearing low-carbon HSLA-100 microalloyed steel

被引：28

作者：

Sohrabi, M. J. ^{[1
]}

Mirzadeh, H. ^{[1
]}

Mehranpour, M. S. ^{[1
]}

Heydarinia, A. ^{[1
]}

Razi, R. ^{[1
]}

机构：

[1] Univ Tehran, Coll Engn, Sch Met & Mat Engn, POB 11155-4563, Tehran, Iran

来源：

ARCHIVES OF CIVIL AND MECHANICAL ENGINEERING | 2019年 / 19卷 / 04期

关键词：

HSLA steel; Age hardening; Secondary hardening; Tensile properties; Charpy V-Notch impact test; STRENGTH LOW-ALLOY; HEAT-TREATMENT; MICROSTRUCTURE; PRECIPITATION; BEHAVIOR;

D O I：

10.1016/j.acme.2019.09.001

中图分类号：

TU [建筑科学];

学科分类号：

0813 ;

摘要：

The precipitation kinetics of HSLA-100 steel and the correlation between tensile and impact properties were studied. According to the modified Johnson-Mehl-Avrami-Kolmogorov (JMAK) analysis and based on the analysis of the time corresponding to the transformed fraction of 0.5 (t(0.5)), the activation energy for the precipitation of copper during aging of martensite was determined as similar to 111 and 105 kJ/mol, respectively. These values are much smaller than the activation energy for the diffusion of Cu in alpha-iron, which was related to the effect of high dislocation density of the quenched martensitic microstructure on the aging process. These results were verified based on the diffusional calculations. Based on the analysis of mechanical behavior, no reasonable correlation was found between strength of the material and the impact energy. However, the impact energy was found to be proportional to the UTS-YS, where the latter is an indicator of the work-hardening capability of the material. This revealed that the work-hardening capacity of the material is a much more important factor for determining the impact toughness compared to its strength. (C) 2019 Politechnika Wroclawska. Published by Elsevier B.V. All rights reserved.

引用

页码：1409 / 1418

页数：10

共 27 条

[1] Amorphization and mechano-crystallization of high-energy ball milled Fe-Ti alloys [J].

Adelfar, Reyhane ;

Mirzadeh, Flamed ;

Ataie, Abolghasem ;

Malekan, Mehdi .

JOURNAL OF NON-CRYSTALLINE SOLIDS, 2019, 520

[2]

Bain E.C., 1940, Functions of the alloying elements in steel

[3] Aging behaviour in copper bearing high strength low alloy steels [J].

Bhagat, AN ;

Pabi, SK ;

Ranganathan, S ;

Mohanty, ON .

ISIJ INTERNATIONAL, 2004, 44 (01) :115-122

[4] INFLUENCE OF MOLYBDENUM ADDITION ON MECHANICAL PROPERTIES OF LOW CARBON HSLA-100 STEEL [J].

Bogucki, R. ;

Pytel, S. M. .

ARCHIVES OF METALLURGY AND MATERIALS, 2014, 59 (03) :859-864

[5] Influence of thermomechanical treatments on the microstructure and mechanical properties of HSLA-100 steel plates [J].

Dhua, SK ;

Mukerjee, D ;

Sarma, DS .

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE, 2003, 34 (02) :241-253

[6] Effect of tempering temperatures on the mechanical properties and microstructures of HSLA-100 type copper-bearing steels [J].

Dhua, SK ;

Ray, A ;

Sarma, DS .

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2001, 318 (1-2) :197-210

[7] The effect of increasing Cu and Ni on a significant enhancement of mechanical properties of high strength low alloy, low carbon steels of HSLA-100 type [J].

Far, A. R. Hosseini ;

Anijdan, S. H. Mousavi ;

Abbasi, S. M. .

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2019, 746 :384-393

[8] Tailoring the microstructure and mechanical properties of AISI 316L austenitic stainless steel via cold rolling and reversion annealing [J].

Kheiri, Sara ;

Mirzadeh, Hamed ;

Naghizadeh, Meysam .

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2019, 759 :90-96

[9] Dual-phase steels microstructure and properties consideration based on artificial intelligence techniques [J].

Krajewski, S. ;

Nowacki, J. .

ARCHIVES OF CIVIL AND MECHANICAL ENGINEERING, 2014, 14 (02) :278-286

[10]

Krauss G., 2015, STEELS PROCESSING ST

← 1 2 3 →