Effect of cryogenic assistance on hole shrinkage during Ti6Al4V drilling

被引：0
作者：
Johan Merzouki
Gérard Poulachon
Frédéric Rossi
Yessine Ayed
Guillaume Abrivard
机构：
[1] HESAM Université,Arts et Metiers Institute of Technology, LaBoMaP
[2] Airbus Central Research and Technology—Technocampus Composites,undefined
[3] Arts et Metiers Institute of Technology,undefined
[4] LAMPA,undefined
来源：
The International Journal of Advanced Manufacturing Technology | 2020年 / 108卷
关键词：
Drilling; Cryogenic assistance; Liquid nitrogen; Hole shrinkage; Cutting forces; Hole geometry;
D O I：
暂无
中图分类号：
学科分类号：
摘要：
This paper focuses on the impact of cryogenic assistance on the drilling of Ti6Al4V titanium alloy. It develops a relation between the phenomenon of hole shrinkage and measurements performed either during or after the machining operation. Indeed, because this phenomenon is apparently strongly associated with heat generation, which is the main issue in titanium alloy drilling, this work proposes to verify the effect of liquid nitrogen cooling on hole shrinkage, quantify it, and then relate it to these measurements. Specifically, the cutting forces and final hole geometry are analyzed and their variations are explained using the collected data on hole shrinkage.
引用
收藏
页码：2675 / 2686
页数：11
相关论文
共 50 条
  • [41] Tool life and hole surface integrity studies for hole-making of Ti6Al4V alloy
    Qing Zhao
    Xuda Qin
    Chunhui Ji
    Yonghang Li
    Dan Sun
    Yan Jin
    The International Journal of Advanced Manufacturing Technology, 2015, 79 : 1017 - 1026
  • [42] Multiresponse optimization of cryogenic drilling on Ti-6Al-4V alloy using topsis method
    L. Shakeel Ahmed
    M. Pradeep Kumar
    Journal of Mechanical Science and Technology, 2016, 30 : 1835 - 1841
  • [43] Effect of cutting parameters on workpiece and tool properties during drilling of Ti-6Al-4V
    Celik, Yahya Hisman
    Yildiz, Hakan
    Ozek, Cebeli
    MATERIALS TESTING, 2016, 58 (06) : 519 - 525
  • [44] Comprehensive machinability assessment of Ti6Al4V alloy during drilling and helical milling using sustainable dry condition
    Hiremath, Anupama
    Malghan, Rashmi L.
    Bolar, Gururaj
    Polishetty, Ashwin
    INTERNATIONAL JOURNAL OF INTERACTIVE DESIGN AND MANUFACTURING - IJIDEM, 2025, 19 (03): : 1987 - 2002
  • [45] An experimental study on abrasive waterjet cutting of CFRP/Ti6Al4V stacks for drilling operations
    Alberdi, A.
    Artaza, T.
    Suarez, A.
    Rivero, A.
    Girot, F.
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2016, 86 (1-4) : 691 - 704
  • [46] Evaluation of drilling process in Ti6Al4V using 3D FE simulation
    Ghassemieh, E. (e.ghassemieh@sheffield.ac.uk), 2013, Inderscience Enterprises Ltd., 29, route de Pre-Bois, Case Postale 856, CH-1215 Geneva 15, CH-1215, Switzerland (13) : 174 - 190
  • [47] INVESTIGATION ON DRILLING PERFORMANCE OF TITANIUM ALLOY TI6AL4V BASED ON RESPONSE SURFACE METHOD
    Zhu, Zhaoju
    Sui, Shaochun
    Sun, Jie
    Li, Jianfeng
    Liu, Kai
    PROCEEDINGS OF THE ASME 12TH INTERNATIONAL MANUFACTURING SCIENCE AND ENGINEERING CONFERENCE - 2017, VOL 3, 2017,
  • [48] An experimental study on abrasive waterjet cutting of CFRP/Ti6Al4V stacks for drilling operations
    A. Alberdi
    T. Artaza
    A. Suárez
    A. Rivero
    F. Girot
    The International Journal of Advanced Manufacturing Technology, 2016, 86 : 691 - 704
  • [49] Deep-hole gun drilling mechanics model of Ti6Al4V alloy based on Johnson and Cook flow stress model
    Li, Liang
    He, Ning
    Hao, XiuQing
    Yang, YinFei
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2019, 104 (9-12) : 4497 - 4508
  • [50] Between-the-Holes Cryogenic Cooling of the Tool in Hole-Making of Ti-6Al-4V and CFRP
    Iqbal, Asif
    Zhao, Guolong
    Zaini, Juliana
    Gupta, Munish Kumar
    Jamil, Muhammad
    He, Ning
    Nauman, Malik Muhammad
    Mikolajczyk, Tadeusz
    Pimenov, Danil Yurievich
    MATERIALS, 2021, 14 (04) : 1 - 19
12345