Machining of Thin-Walled Workpieces: Two-Dimensional Finite-Element Modeling

被引：0
作者：
Kandarov I.V. [1 ]
Starovoitov S.V. [1 ]
Evseev A.O. [1 ]
机构：
[1] Tekhnopark, Ufa
来源：
Russian Engineering Research | 2022年 / 42卷 / Suppl 1期
关键词：
cutting; finite-element modeling; geometric accuracy; pliability; production conditions; thin-walled parts; turning;
D O I：
10.3103/S1068798X23010124
中图分类号：
学科分类号：
摘要：
Abstract: The machining of large thin-walled rings is considered. The influence of the cutter geometry and the cutting conditions on the machining precision is analyzed by the finite-element method. Production experiments are compared with the theoretical analysis. Practical recommendations are formulated. © 2022, Allerton Press, Inc.
引用
收藏
页码：S77 / S80
页数：3
相关论文
共 10 条
[1]  
Usmanov B.F., Starovoitov S.V., Khadiullin S.K., Using experiments to construct mathematical models for machinability characteristics of a heat resistant aluminum alloy, J. Eng. Sci. Technol. Rev, 7, pp. 51-54, (2014)
[2]  
Basharov R.R., Kil'Metova L.R., Starovoitov S.V., Et al., Analysis of causes and sources of occurrence of residual stress, Vestn. Ufimsk. Gos. Aviats. Tekh. Univ, 22, 82, pp. 3-11, (2018)
[3]  
Poletaev V.A., Tekhnologiya Avtomatizirovannogo Proizvodstva Lopatok Gazoturbinnykh Dvigatelei (Technology of Automated Production of the Blades of Gas Turbine Engines), (2006)
[4]  
Basharov R.R., Krasnikov I.P., Gaimalov A.F., Khadiullin S.K., Research of the relationship of vibration and roughness when milling, Vestn. Ufimsk. Gos. Aviats. Tekh. Univ, 24, 89, pp. 3-9, (2020)
[5]  
Gafarov R.K., Zhernakov V.S., O Soprotivlenii Materialov: Uchebnoe Posobie (What You Need to Know about the Resistance of Materials: Manual), (2001)
[6]  
Postnov V.V., Yur'Ev V.L., Starovoitov S.V., . Tikhonova A.A., Investigation in the influence of the energy dissipation factors during cutting on the tool-wear rate, Aviats. Prom-St., 2, pp. 35-40, (2015)
[7]  
Postnov V.V., Khadiullin S.K., Starovoitov S.V., Predicting the cutting properties of hard alloys for the manufacture of components used in gas-turbine engines, Russ. Eng. Res, 36, pp. 496-501, (2016)
[8]  
Computational and experimental method of machining blades for gas turbine engines on mechatronic machines with error compensation, Vestn, Ufimsk. Gos. Aviats. Tekh. Univ, 16, 7, pp. 145-153, (2012)
[9]  
Starovoitov S.V., Sattarov M.E., Khadiullin S.K., Constructive assessment of an attainable accuracy at large-size thin-walled housing rings machining by modelling of cutting force effect, J. Eng. Sci. Technol. Rev, 13, pp. 166-170, (2020)
[10]  
Postnov V.V., Khadiullin S.K., Starovoitov S.V., Predicting the cutting properties of hard alloys for the manufacture of components used in gas-turbine engines, Russ. Eng. Res, 36, pp. 496-501, (2016)
1