Investigation on Microstructure and Dry Sliding Wear Behavior of a Novel Fe-Cr-B-C-Al-Si-Mn Composite Coatings on 2Cr13 Steel by Laser Cladding

被引：0
作者：
Jian Gu
Dongqing Li
Shengchun Liu
Jiajun Si
Songlin Cai
Xuliang Liu
Peng Liu
Kaiming Wang
机构：
[1] China Electric Power Research Institute,Hunan Provincial Key Laboratory of Intelligent Manufacturing Technology for High
[2] Changsha University of Science and Technology,performance Mechanical Equipment, College of Automobile and Mechanical Engineering
[3] Tsinghua University,State Key Laboratory of Tribology, Department of Mechanical Engineering
来源：
Journal of Materials Engineering and Performance | 2022年 / 31卷
关键词：
Fe-based composite coatings; laser cladding; microstructure; TEM; wear resistance;
D O I：
暂无
中图分类号：
学科分类号：
摘要：
A novel Fe-Cr-B-C-Al-Si-Mn composite coating was designed and synthesized on 2Cr13 steel substrate using laser cladding technique in this study. The microstructure evolution, microhardness and wear resistance of the composite coating were investigated. The results showed that the microstructure of the coating was mainly composed of α-(Fe,Cr,Al) martensite, retained γ-Fe, and the eutectic comprised of CrFeB, M3(C,B)2, M2(B,C) and M23(C,B)6. The average microhardness of the coating (742.1 HV0.5) was 3.95 times compared with the 2Cr13 steel substrate, and the wear resistance was enhanced by 12.5 times compared with the 2Cr13 steel substrate. The wear mechanisms were dominated by abrasive wear and oxidative wear.
引用
收藏
页码：2381 / 2390
页数：9
相关论文
共 221 条
[1]  
Cao R(2018)Effects of the Rolling Temperature on the Microstructure and Mechanical properTies of 2Cr13/316L Laminated COMPOSITES Prepared by Accumulative Roll-Bonding (ARB) Mater. Charact. 139 153-164
[2]  
Zhao XK(2009)Microstructure and Tribological Characteristics of Nitrided Layer on 2Cr13 Steel in air and Vacuum Surf. Coat. Technol. 204 705-712
[3]  
Ding Y(2008)Microstructure, Mechanical and Wear Properties of TiC Particulate Reinforced 2Cr13 Steel by In Situ Reaction and Electroslag Remelting Ironmaking Steelmaking 35 387-395
[4]  
Zhang XB(2018)Effects of Rolling Temperature on the Microstructure and Properties of 2Cr13/316L/9Cr18MoV Stainless Steel Composite Plate Fabricated by Hot-Rolling Bonding Process J. Mater. Eng. Perform. 27 3978-3993
[5]  
Jiang XX(2012)Influence of Heat Treatment and Laser Shock Processing on Impact Toughness of 2Cr13 Martensite Stainless Steel Chin. J. Lasers 39 1-4
[6]  
Yan YJ(2019)Influence of Heat Treatment on Microstructures and Mechanical Properties of K447A Cladding Layers Obtained by Laser Solid Forming J. Alloys Compd. 790 703-715
[7]  
Chen JH(2000)Magnetron Sputtering: A Review of Recent Developments and Applications Vacuum 56 159-172
[8]  
Yang JQ(2019)Robust, Self-Cleaning, Anti-Fouling, Superamphiphobic Soy Protein Isolate Composite Films Using Spray-Coating Technique with Fluorinated HNTs/SiO Compos. Pt. B-Eng. 174 107002-19
[9]  
Liu Y(2019)Determination of the Structural, Morphological and Optical Properties of Graphene Doped SnO Thin Films Deposited by Using Thermionic Vacuum Arc Technique Phys. B Condens. Matter. 569 14-484
[10]  
Ye ZY(2019)Electrochemical Surface Modification of Polyacrylonitrile-Based Ultrahigh Modulus Carbon Fibers and its Effect on the Interfacial Properties of UKMCF/EP Composites Compos. Pt. B-Eng. 164 476-189
12345678910