Effects of ultrasonication time on stability, dynamic viscosity, and pumping power management of MWCNT-water nanofluid: an experimental study

被引:0
作者
Amin Asadi
Ibrahim M. Alarifi
机构
[1] Duy Tan University,Institute of Research and Development
[2] Duy Tan University,Faculty of Natural Sciences
[3] Majmaah University,Department of Mechanical and Industrial Engineering, College of Engineering
[4] Majmaah University,Engineering and Applied Science Research Center
来源
Scientific Reports | / 10卷
关键词
D O I
暂无
中图分类号
学科分类号
摘要
It is known that ultrasonication has a certain effect on thermophysical properties and heat transfer of nanofluids. The present study is the continuation of the authors’ previous research on the effects of ultrasonication on the thermophysical properties of Multi-Walled Carbon Nanotubes (MWCNTs)-water nanofluid. Investigating the effects of ultrasonication time on samples’ stability, rheological properties, and pumping power of a water-based nanofluid containing MWCNTs nanoparticle is the main objective of the present study. The two-step method has been employed to prepared the samples. Moreover, a probe-type ultrasonic device has been used, and different ultrasonication times have been applied. The samples’ stability is investigated in different periods. The results revealed that prolonging the ultrasonication time to 60 min leads to improving the samples’ stability while prolonging ultrasonication time to higher than 60 min resulted in deteriorating the stability. As for dynamic viscosity, it is observed that increasing ultrasonication time to 60 min leads to decreasing the dynamic viscosity of the samples. As for pumping power, it is observed that the maximum increase in fanning friction factor ratio is less than 3%, which shows that adding MWCNTs to water does not impose a considerable penalty in the required energy for pumping power.
引用
收藏
相关论文
共 155 条
[1]  
Asadi M(2018)An experimental and theoretical investigation on the effects of adding hybrid nanoparticles on heat transfer efficiency and pumping power of an oil-based nanofluid as a coolant fluid Int. J. Refrig. 89 83-92
[2]  
Asadi A(2019)On the rheological properties of MWCNT-TiO2/oil hybrid nanofluid: an experimental investigation on the effects of shear rate, temperature, and solid concentration of nanoparticles Powder Technol. 355 157-162
[3]  
Aberoumand S(2015)Thermal conductivity and viscosity of Mg(OH)2-ethylene glycol nanofluids J. Thermal Anal. Calorimetry 120 1145-1149
[4]  
Alarifi IM(2019)On the thermal characteristics of a manifold microchannel heat sink subjected to nanofluid using two-phase flow simulation Int. J. Heat Mass Transf. 143 118518-10
[5]  
Alkouh AB(2018)A guideline towards easing the decision-making process in selecting an effective nanofluid as a heat transfer fluid Energy Convers. Manag. 175 1-586
[6]  
Ali V(2018)An experimental and theoretical investigation on heat transfer capability of Mg (OH)2/MWCNT-engine oil hybrid nano-lubricant adopted as a coolant and lubricant fluid Appl. Therm. Eng. 129 577-157
[7]  
Nguyen HM(2018)Heat transfer enhancement using nanofluids for cooling a central processing unit (CPU) system J. Adv. Res. Fluid Mech. Thermal Sci. 51 145-410
[8]  
Asadi A(2020)On the heat transfer effectiveness and pumping power assessment of a diamond-water nanofluid based on thermophysical properties: an experimental study Powder Technol. 373 397-16
[9]  
Hemmat Esfe M(2020)On the thermal performance of a fractal microchannel subjected to water and kerosene carbon nanotube nanofluid Sci. Rep. 10 1-50
[10]  
Saedodin S(2020)Thermal and fluid dynamics performance of MWCNT-water nanofluid based on thermophysical properties: an experimental and theoretical study Sci. Rep. 10 5185-145