Preheating-assisted solid-state friction stir repair of Al-Mg-Si alloy plate at different rotational speeds

被引:21
作者
Wang, Hui [1 ]
Li, Yidi [1 ]
Zhang, Ming [1 ]
Gong, Wei [1 ]
Lai, Ruilin [2 ]
Li, Yunping [1 ]
机构
[1] Cent South Univ, State Key Lab Powder Met, Changsha 410083, Peoples R China
[2] Cent South Univ, Res Inst Light Alloy, Changsha 410083, Peoples R China
关键词
additive friction stir deposition; structural repair; tool rotation speed; Al alloy; MECHANICAL-PROPERTIES; MICROSTRUCTURE; BEHAVIOR;
D O I
10.1007/s12613-023-2772-9
中图分类号
T [工业技术];
学科分类号
08 ;
摘要
Additive friction stir deposition (AFSD) is a novel structural repair and manufacturing technology has become a research hotspot at home and abroad in the past five years. In this work, the microstructural evolution and mechanical performance of the Al-Mg-Si alloy plate repaired by the preheating-assisted AFSD process were investigated. To evaluate the tool rotation speed and substrate preheating for repair quality, the AFSD technique was used to additively repair 5 mm depth blind holes on 6061 aluminum alloy substrates. The results showed that preheat-assisted AFSD repair significantly improved joint bonding and joint strength compared to the control non-preheat substrate condition. Moreover, increasing rotation speed was also beneficial to improve the metallurgical bonding of the interface and avoid volume defects. Under preheating conditions, the UTS and elongation were positively correlated with rotation speed. Under the process parameters of preheated substrate and tool rotation speed of 1000 r/min, defect-free specimens could be obtained accompanied by tensile fracture occurring in the substrate rather than the repaired zone. The UTS and elongation reached the maximum values of 164.2 MPa and 13.4%, which are equivalent to 99.4% and 140% of the heated substrate, respectively.
引用
收藏
页码:725 / 736
页数:12
相关论文
共 60 条
[1]   Advances in simulation and experimental study on intermetallic formation and thermomechanical evolution of Al-Cu composite with Zn interlayer: Effect of spot pass and shoulder diameter during the pinless friction stir spot welding process [J].
Abdollahzadeh, Amin ;
Bagheri, Behrouz ;
Vaneghi, Alireza H. ;
Shamsipur, Ali ;
Mirsalehi, Seyyed E. .
PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART L-JOURNAL OF MATERIALS-DESIGN AND APPLICATIONS, 2023, 237 (06) :1475-1494
[2]   Additive friction stir deposition of SS316: Effect of process parameters on microstructure evolution [J].
Agrawal, Priyanshi ;
Haridas, Ravi Sankar ;
Yadav, Surekha ;
Thapliyal, Saket ;
Dhal, Abhijeet ;
Mishra, Rajiv S. .
MATERIALS CHARACTERIZATION, 2023, 195
[3]   Processing-structure-property correlation in additive friction stir deposited Ti-6Al-4V alloy from recycled metal chips [J].
Agrawal, Priyanshi ;
Haridas, Ravi Sankar ;
Yadav, Surekha ;
Thapliyal, Saket ;
Gaddam, Supreeth ;
Verma, Ravi ;
Mishra, Rajiv S. .
ADDITIVE MANUFACTURING, 2021, 47
[4]   Characterization of the fatigue behavior of additive friction stir-deposition AA2219 [J].
Anderson-Wedge, K. ;
Avery, D. Z. ;
Daniewicz, S. R. ;
Sowards, J. W. ;
Allison, P. G. ;
Jordon, J. B. ;
Amaro, R. L. .
INTERNATIONAL JOURNAL OF FATIGUE, 2021, 142
[5]   Evaluation of Microstructure and Mechanical Properties of Al-Zn-Mg-Cu Alloy Repaired via Additive Friction Stir Deposition [J].
Avery, D. Z. ;
Cleek, C. E. ;
Phillips, B. J. ;
Rekha, M. Y. ;
Kinser, R. P. ;
Rao, H. M. ;
Brewer, L. N. ;
Allison, P. G. ;
Jordon, J. B. .
JOURNAL OF ENGINEERING MATERIALS AND TECHNOLOGY-TRANSACTIONS OF THE ASME, 2022, 144 (03)
[6]   Influence of a non-rotating shoulder on heat generation, microstructure and mechanical properties of dissimilar AA2024/AA7050 FSW joints [J].
Barbini, Alessandro ;
Carstensen, Jan ;
dos Santos, Jorge F. .
JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY, 2018, 34 (01) :119-127
[7]   The effect of solutionizing and artificial aging on the microstructure and mechanical properties in solid-state additive manufacturing of precipitation hardened Al-Mg-Si alloy [J].
Beck, S. C. ;
Rutherford, B. A. ;
Avery, D. Z. ;
Phillips, B. J. ;
Rao, H. ;
Rekha, M. Y. ;
Brewer, L. N. ;
Allison, P. G. ;
Jordon, J. B. .
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2021, 819
[8]  
Gadakh V.S., 2013, Journal of Materials Research and Technology, V2, P370, DOI [10.1016/j.jmrt.2013.10.003, DOI 10.1016/J.JMRT.2013.10.003]
[9]   In situ investigation into temperature evolution and heat generation during additive friction stir deposition: A comparative study of Cu and Al-Mg-Si [J].
Garcia, David ;
Hartley, W. Douglas ;
Rauch, Hunter A. ;
Griffiths, R. Joey ;
Wang, Rongxuan ;
Kong, Zhenyu J. ;
Zhu, Yunhui ;
Yu, Hang Z. .
ADDITIVE MANUFACTURING, 2020, 34
[10]   Influence of Preheating Temperature on the Microstructure and Mechanical Properties of 6061/TA1 Composite Plates Fabricated by AFSD [J].
Gong, Wei ;
Li, Yidi ;
Zhang, Ming ;
Wang, Hui ;
Liu, Qinglin ;
Zeng, Ziming ;
Ma, Kuo ;
Yang, Biaobiao ;
Lai, Ruilin ;
Li, Yunping .
MATERIALS, 2023, 16 (17)