Optimization analysis of high temperature heat pump coupling to desiccant wheel air conditioning system

被引：0

作者：

Sheng Y. ^{[1
]}

Zhang Y. ^{[1
]}

Fang L. ^{[2
]}

Nie J. ^{[2
]}

Ma L. ^{[1
]}

机构：

[1] School of Environmental Science and Engineering, Tianjin University

[2] International Centre for Indoor Environment and Energy, Technical University of Denmark

来源：

Transactions of Tianjin University | 2014年 / 20卷 / 03期

关键词：

adiabatic effectiveness; dehumidification; desiccant wheel; performance optimization;

D O I：

10.1007/s12209-014-2191-0

中图分类号：

学科分类号：

摘要：

The high temperature heat pump and desiccant wheel (HTHP&DW) system can make full use of heat released from the condenser of heat pump for DW regeneration without additional heat. In this study, DW operation in the HTHP&DW system was investigated experimentally, and the optimization analysis of HTHP&DW system was carried out. The performance of DW had influence on the dehumidification (evaluated by dehumidification and regeneration effectiveness) and cooling load (evaluated by thermal and adiabatic effectiveness). The results show that the enthalpy increase occurred in all the experiments. Compared to the isosteric heat, heat accumulation in the desiccant and matrix material and heat leakage from regeneration side to process side have greater influence on the adiabatic effectiveness. Higher regeneration temperature leads to lower adiabatic effectiveness that increases more cooling load of the system. When the regeneration temperature is 63°C, the maximal dehumidification effectiveness is 35.4% and the satisfied adiabatic effectiveness is 88%, which contributes to the optimal balance between dehumidification and cooling. © 2014 Tianjin University and Springer-Verlag Berlin Heidelberg.

引用

页码：182 / 188

页数：6

共 16 条

[1]

Hao H., Zhang Y.F., Zhou G.B., Feasibility study of moderate or high temperature heat pump coupling to desiccant wheel hybrid system [J], Journal of Shenyang Jianzhu University: Natural Science, 24, 4, pp. 675-678, (2008)

[2]

Zhang Y.F., Hu X.W., Miao Z.S., Et al., Cycle performance of heat pump in desiccant cooling system [J], Journal of Chemical Industry and Engineering, 60, 9, pp. 2177-2182, (2009)

[3]

Sheng Y., Zhang Y.F., Deng N., Et al., Experimental analysis on performance of high temperature heat pump and desiccant wheel system [J], Energy and Buildings, 66, pp. 505-513, (2013)

[4]

Zhang L.Z., Niu J.L., Performance comparisons of desiccant wheels for air dehumidification and enthalpy recovery, Applied Thermal Engineering, 22, 12, pp. 1347-1367, (2002)

[5]

Nia F.E., Van Paassen D., Saidi M.H., Modeling and simulation of desiccant wheel for air conditioning, Energy and Buildings, 38, 10, pp. 1230-1239, (2006)

[6]

Jia C.X., Dai Y.J., Wu J.Y., Performance optimization of silica gel-lithium chloride composite desiccant dehumidification wheel[J], Gas and Heat, 28, 10, (2008)

[7]

Dai Y.J., Wang R.Z., Zhang H.F., Parameter analysis to improve rotary desiccant dehumidification using a mathematical model, International Journal of Thermal Sciences, 40, 4, pp. 400-408, (2001)

[8]

Zhang X.J., Liu H.X., Wang R.Z., Shi F., Numerical simulation of heat transfer in regenerator of solid adsorption refrigeration system, Renewable Energy, 26, 4, pp. 599-610, (2002)

[9]

Kodama A., Hirayama T., Goto M., Hirose T., Critoph R.E., The use of psychrometric charts for the optimisation of a thermal swing desiccant wheel, Applied Thermal Engineering, 21, 16, pp. 1657-1674, (2001)

[10]

Zhang X.J., Dai Y.J., Wang R.Z., Psychrometric analysis and optimization of a desiccant rotary wheel [J], Journal of Engineering Thermophysics, 26, 5, pp. 733-735, (2005)

← 1 2 →