Effect of Y Alloying on Microstructure and Mechanical Properties of Ti-48Al Alloy

被引：0
|
作者：
Jianglei Fan
Zexin Wei
Liubo Liang
Ying Li
Shen Wu
Yan Wang
Xiangkui Zhou
Jianxiu Liu
机构：
[1] Zhengzhou University of Light Industry,Institute of Mechanical and Electrical Engineering, Henan Key Laboratory of Intelligent Manufacturing of Mechanical Equipment
[2] Zhengzhou University of Light Industry,Henan Engineering Research Center of Advanced Materials Processing and Testing
来源：
JOM | 2022年 / 74卷
关键词：
D O I：
暂无
中图分类号：
学科分类号：
摘要：
The effects of Y content (ranged from 0.1 at.% to 2.0 at.%) on the microstructure evolution and mechanical properties of Ti-48Al (at.%) alloy were investigated. The addition of Y can significantly refine the microstructure. The grain size is decreased with increasing Y content. The microhardness of Ti-48Al-xY (at.%) is increased with increasing Y content because of the volume fraction increment of Al3Y and Y2O3 with higher hardness. When the Y content increased to 1.0 at.%, the microhardness of the Ti-48Al-xY (at.%) alloys tends to be stable. With the increase of Y content, the compression strength of Ti-48Al-xY (at.%) alloys is increased first and then decreased. The Ti-48Al-0.5Y (at.%) alloy exhibits the best compression strength (2229 MPa), which is 15% higher than that of Ti-48Al (at.%) alloy. The fracture mechanism of the alloy is brittle fracture. The fracture modes are mainly translamellar and interlamellar fracture.
引用
收藏
页码：4806 / 4816
页数：10
相关论文
共 50 条
  • [31] Microstructure and Mechanical Properties of Al-4.9Ni-4.9Ti Alloy Prepared by Mechanical Alloying
    Guoxian LIANG
    Zhichao LI and Erde WANG (College of Materials Science and Engineering
    JournalofMaterialsScience&Technology, 1995, (03) : 209 - 212
  • [32] Effect of mechanical alloying on the microstructure and properties of Al-Sn-Mg alloy
    Patel, J.
    Morsi, K.
    JOURNAL OF ALLOYS AND COMPOUNDS, 2012, 540 : 100 - 106
  • [33] Microstructure and mechanical properties of Al-4.9Ni-4.9Ti alloy prepared by mechanical alloying
    Liang, Guoxian
    Li, Zhichao
    Wang, Erde
    Journal of Materials Science and Technology, 1995, 11 (03): : 209 - 212
  • [34] Microstructure and Fatigue Properties of Ti-48Al Alloy Fabricated by the Twin-Wire Plasma Arc Additive Manufacturing
    Xi Zhang
    Qinghua Lu
    Peilei Zhang
    Zhishui Yu
    Chen Shen
    Lin Wang
    Xueming Hua
    Journal of Materials Engineering and Performance, 2022, 31 : 8250 - 8260
  • [35] Synthesis of Ti-Al alloy by mechanical alloying and its microstructure
    Nobuki, Tohru
    Kuji, Toshiro
    JOURNAL OF THE JAPAN INSTITUTE OF METALS, 2008, 72 (03) : 236 - 243
  • [36] Influence of purity level on the structural evolution and the mechanical properties of the Ti-48Al alloys
    Hitier, P
    Bonnentien, JL
    Bertrand, C
    Cornet, M
    Bigot, J
    PHYSICA STATUS SOLIDI A-APPLIED RESEARCH, 1997, 160 (02): : 541 - 547
  • [37] Effect of Cr addition on microstructures and nanohardness of rapidly solidified Ti-48Al alloy
    Zhu, D. D.
    Wang, H. W.
    Qi, J. Q.
    Zou, C. M.
    Wei, Z. J.
    MATERIALS SCIENCE AND TECHNOLOGY, 2012, 28 (12) : 1385 - 1390
  • [38] Effect of Nb on pore structure and tensile property of Ti-48Al cellular alloy
    Wang, Y. H.
    Lin, J. P.
    He, Y. H.
    Wang, Y. L.
    Chen, G. L.
    JOURNAL OF ALLOYS AND COMPOUNDS, 2008, 456 (1-2) : 297 - 303
  • [39] Effect of rapid heat treatment on a microstructure and mechanical properties of Ti-48Al-3Cr alloy
    Ivasishin, OM
    Savvakin, DG
    METALLOFIZIKA I NOVEISHIE TEKHNOLOGII, 1999, 21 (12): : 76 - 82
  • [40] Effect of rapid heat treatment on the microstructure and mechanical properties of a Ti-48Al-3Cr alloy
    Ivasishin, O.M.
    Sawakin, D.G.
    Metal Physics and Advanced Technologies, 2001, 19 (12): : 1659 - 1666
12345