Sharpening helical bits with curvilinear cutting edges at the rear surface

被引：4
|
作者：
Petukhov Y.E. [1 ]
Vodovozov A.A. [1 ]
机构：
[1] Stankin Moscow State Technical University, Moscow
来源：
Russian Engineering Research | 2015年 / 35卷 / 9期
关键词：
curvilinear cutting edge; helical bit; rear surface; sharpening;
D O I：
10.3103/S1068798X15090178
中图分类号：
学科分类号：
摘要：
Sharpening of the curvilinear cutting edges at the rear surface of helical bits is considered. A mathematic model of the rear surfaces takes account of the bit parameters and the distribution of the rear angles along the cutting edge. The position of the grinding wheel in sharpening is determined. © 2015, Allerton Press, Inc.
引用
收藏
页码：670 / 673
页数：3
相关论文
共 50 条
  • [1] Sharpening of hob cutting edges with helical flutes
    Yoshino, H
    Ohshima, F
    PROCEEDINGS OF THE INTERNATIONAL CONFERENCE ON MECHANICAL TRANSMISSIONS, 2001, : 115 - 119
  • [2] DYNAMICS OF DRILL BITS WITH CUTTING EDGES OF VARYING PARAMETERS
    Dombovari, Zoltan
    Stepan, Gabor
    PROCEEDINGS OF THE ASME INTERNATIONAL DESIGN ENGINEERING TECHNICAL CONFERENCES AND COMPUTERS AND INFORMATION IN ENGINEERING CONFERENCE, 2013, VOL 7B, 2014,
  • [3] Curvilinear cutting edge of a helical bit with uniform life
    Petukhov Y.E.
    Vodovozov A.A.
    Russian Engineering Research, 2014, 34 (10) : 645 - 648
  • [4] Determining the cutting forces at the rear tool surface
    Lipatov A.A.
    Chigirinskii Y.L.
    Kormilitsyn S.I.
    Russian Engineering Research, 2010, 30 (11) : 1158 - 1160
  • [5] DEVICE FOR HELICAL SURFACE GENERATION WITH TILTING SLIDER USED FOR SHARPENING MILLS WITH HELICAL PROFILE
    Micaciu, Alexandru
    Vuscan, Ioan Gheorghe
    Morariu-Gligor, Radu Mircea
    ACTA TECHNICA NAPOCENSIS SERIES-APPLIED MATHEMATICS MECHANICS AND ENGINEERING, 2014, 57 (04): : 553 - 558
  • [6] Wear at the tool’s rear surface in discontinuous cutting
    Krasil’nikov A.Y.
    Zakharov P.N.
    Russian Engineering Research, 2015, 35 (06) : 421 - 422
  • [7] METHOD FOR CONICAL SHARPENING OF MULTI-FLUTE HELICAL DRILL WITH CURVED CUTTING EDGE
    Fetecau, Catalin
    Teodor, Virgil
    Dumitrascu, Nicolae
    Oancea, Nicolae
    MODTECH 2010: NEW FACE OF TMCR, PROCEEDINGS, 2010, : 275 - 278
  • [8] A SYSTEMS-APPROACH TO SURFACE ENGINEERING OF CUTTING EDGES
    SARWAR, M
    AHMED, W
    MATERIALS WORLD, 1994, 2 (03) : 141 - 143
  • [9] THE MEASUREMENT OF THE CUTTING FORCE AT GRINDING A HELICAL SURFACE
    Micaciu, Alexandru
    Vuscan, Ioan Gheorghe
    Morariu-Gligor, Radu Mircea
    ACTA TECHNICA NAPOCENSIS SERIES-APPLIED MATHEMATICS MECHANICS AND ENGINEERING, 2014, 57 (04): : 559 - 562
  • [10] Influence of cutting conditions on the stress at tool's rear surface
    Pimenov D.Y.
    Guzeev V.I.
    Koshin A.A.
    Russian Engineering Research, 2011, 31 (11) : 1151 - 1155
12345