A Comparative Study on Tensile and Fracture Behavior of Al–Mg Alloy Processed Through Cryorolling and Cryo Groove Rolling

被引：26

作者：

Yogesha K.K. ^{[1
]}

Kumar N. ^{[1
]}

Joshi A. ^{[1
]}

Jayaganthan R. ^{[1
,2
]}

Nath S.K. ^{[1
]}

机构：

[1] Department of Metallurgical and Materials Engineering & Centre of Nanotechnology, Indian Institute of Technology Roorkee, Roorkee

[2] Department of Engineering Design, Indian Institute of Technology Madras, Chennai

来源：

Metallography, Microstructure, and Analysis | 2016年 / 5卷 / 03期

关键词：

Fractography; Fracture strength; Groove rolling; Microstructure;

D O I：

10.1007/s13632-016-0282-0

中图分类号：

学科分类号：

摘要：

In the present work, Al–Mg alloy (AA 5052) was subjected to cryorolling followed by post-deformation annealing, in order to investigate its effect on tensile and fracture behavior. The solution-treated Al alloys were cryorolled (CR) and cryo groove rolled to different true strains. The microstructure of the samples (deformed and post-annealed) was characterized by optical microscopy, x-ray diffraction, and TEM to substantiate the mechanisms of grain refinement and its influence on tensile and fracture properties. Fractography of the tensile as well as three-point bending test samples was carried out using a scanning electron microscope (SEM) to reveal the fracture mode. The deformed samples (90% thickness reduction) exhibit significant improvement in strength (291 MPa) and hardness (110 HV) in CR samples and 313 MPa and 122 HV in cryo groove rolled samples, which is due to high dislocation density and grain size reduction. Post-annealing of the deformed samples (90% thickness reduction) led to improvement in its ductility as well as fracture toughness. The cryo groove rolled samples and post-annealed samples have shown better fracture toughness (142 kJ/m2) as compared to cryo rolled samples (29 kJ/m2) due to the relatively larger grain and dimples as observed from TEM and fractography studies. © 2016, Springer Science+Business Media New York and ASM International.

引用

页码：251 / 263

页数：12

共 49 条

[1]

Singh D., Rao P.N., Jayaganthan R., Effect of deformation temperature on mechanical properties of ultrafine grained Al–Mg alloys processed by rolling, Mater. Des., 50, pp. 646-655, (2013)

[2]

Kang U.G., Lee J.C., Jeong S.W., Nam W.J., The improvement of strength and ductility in ultra-fine grained 5052 Al alloy by cryogenic-and warm-rolling, J. Mater. Sci., 45, 17, pp. 4739-4744, (2010)

[3]

Song H.R., Kim Y.S., Nam W.J., Mechanical properties of ultrafine grained 5052 Al alloy produced by accumulative roll-bonding and cryogenic rolling, Met. Mater. Int., 12, 1, pp. 7-12, (2006)

[4]

Lee S.H., Saito Y., Sakai T., Utsunomiya H., Microstructures and mechanical properties of 6061 aluminum alloy processed by accumulative roll-bonding, Mater. Sci. Eng. A, 325, 1, pp. 228-235, (2002)

[5]

Tsuji N., Saito Y., Lee S.H., ARB (accumulative roll-bonding) and other new techniques to produce bulk ultrafine grained materials, Adv. Eng. Mater., 5, 5, pp. 338-344, (2003)

[6]

Saito Y., Utsunomiya H., Tsuji N., Sakai T., Novel ultra-high straining process for bulk materials—development of the accumulative roll-bonding (ARB) process, Actamaterialia, 47, 2, pp. 579-583, (1999)

[7]

Ruppert M., Schunk C., Hausmann D., Hoppel H.W., Global and local strain rate sensitivity of bimodal Al-laminates produced by accumulative roll bonding, Acta Mater., 103, pp. 643-650, (2016)

[8]

Gashti S.O., Fattah-alhosseini A., Mazaheri Y., Effects of grain size and dislocation density on strain hardening behavior of ultrafine grained AA1050 processed by accumulative roll bonding, J. Alloy. Compd., 658, pp. 854-861, (2016)

[9]

Eizadjou M., Talachi A.K., Manesh H.D., Investigation of structure and mechanical properties of multi-layered Al/Cu composite produced by accumulative roll bonding (ARB) process, Compos. Sci. Technol., 68, 9, pp. 2003-2009, (2008)

[10]

Chen Y.C., Huang Y.Y., Chang C.P., Kao P.W., The effect of extrusion temperature on the development of deformation microstructures in 5052 aluminium alloy processed by equal channel angular extrusion, Acta Mater., 51, 7, pp. 2005-2015, (2003)

← 1 2 3 4 5 →