Cutting characteristics in the end milling of stainless steel

被引：1
|
作者：
Grubyi S.V. [1 ]
机构：
[1] Bauman Moscow State Technical University, Moscow
来源：
Russian Engineering Research | 2017年 / 37卷 / 2期
关键词：
end mills; hard alloys; milling; polynomial equations; stainless steel; tool life; tool wear; torque;
D O I：
10.3103/S1068798X17020083
中图分类号：
学科分类号：
摘要：
A method is proposed for calculating the cutting characteristics in the end milling of stainless steel workpieces. The calculation is based on analysis of the parameters for the chip-formation zone and takes account of softening of the material under the action of the cutting temperature. The calculated tool life and the torque are approximated by polynomial equations, which may be used to calculate the constraints on milling and to optimize the machining conditions. © 2017, Allerton Press, Inc.
引用
收藏
页码：125 / 133
页数：8
相关论文
共 50 条
  • [1] Experimental study on cutting force in end milling of stainless steel
    Xue, ZP
    Xu, YS
    Niu, WT
    Li, YC
    Dong, H
    ADVANCES IN GRINDING AND ABRASIVE PROCESSES, 2004, 259-2 : 441 - 445
  • [2] Cutting fluid efficiency in end milling of AISI 304-stainless steel
    Abou-El-Hossein, K. A.
    INDUSTRIAL LUBRICATION AND TRIBOLOGY, 2008, 60 (2-3) : 115 - 120
  • [3] Cutting edge wear in high-speed stainless steel end milling
    Malekan, Mohammad
    Bloch-Jensen, Camilla D.
    Zolbin, Maryam Alizadeh
    Orskov, Klaus B.
    Jensen, Henrik M.
    Aghababaei, Ramin
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2021, 114 (9-10) : 2911 - 2928
  • [4] Cutting edge wear in high-speed stainless steel end milling
    Mohammad Malekan
    Camilla D. Bloch-Jensen
    Maryam Alizadeh Zolbin
    Klaus B. Ørskov
    Henrik M. Jensen
    Ramin Aghababaei
    The International Journal of Advanced Manufacturing Technology, 2021, 114 : 2911 - 2928
  • [5] Method of Tool Wear Control during Stainless Steel End Milling
    Pyatykh, A. S.
    Savilov, A., V
    Timofeev, S. A.
    JOURNAL OF FRICTION AND WEAR, 2021, 42 (04) : 263 - 267
  • [6] Method of Tool Wear Control during Stainless Steel End Milling
    A. S. Pyatykh
    A. V. Savilov
    S. A. Timofeev
    Journal of Friction and Wear, 2021, 42 : 263 - 267
  • [7] Cutting Tool Geometry for Plunge Milling - Process Optimization for a Stainless Steel
    Witty, Martin
    Bergs, Thomas
    Schaefer, Alexander
    Cabral, Gustavo
    FIFTH CIRP CONFERENCE ON HIGH PERFORMANCE CUTTING 2012, 2012, 1 : 506 - 511
  • [8] End milling of stainless steel using electrolyzed reduced water
    Faculty of Education, Shinshu University, 6 Nishinagano, Nagano-shi, Nagano, 380-8544, Japan
    Nihon Kikai Gakkai Ronbunshu C, 2006, 6 (1987-1994): : 1987 - 1994
  • [9] Comparative Analysis of Different Cutting Milling Strategies Applied in Duplex Stainless Steel
    Amaro, Paulo
    Ferreira, Pedro
    Simoes, Fernando
    23RD INTERNATIONAL CONFERENCE ON MATERIAL FORMING, 2020, 47 : 517 - 524
  • [10] Cutting Force Prediction of Stainless Steel in High-speed Milling
    Xie, Xiaozheng
    Yao, Yunping
    Zhao, Rongzhen
    Jin, Wuyin
    MATERIALS PROCESSING TECHNOLOGY II, PTS 1-4, 2012, 538-541 : 1369 - 1372
12345