Effect of liquid nitrogen jet impingement angle on machinability of titanium alloy in cryogenic cooling

被引:0
|
作者
Fengbiao Wang
Yiming Qin
Li Sun
机构
[1] Shenyang Ligong University,School of Mechanical Engineering
[2] Dalian Jiaotong University,School of Mechanical Engineering
来源
The International Journal of Advanced Manufacturing Technology | 2024年 / 131卷
关键词
Titanium alloy; LN; cooling efficiency; LN; boiling; Jet impingement; Machinability;
D O I
暂无
中图分类号
学科分类号
摘要
In order to further research the effect of cryogenic cooling, the cooling capacity of LN2 jet was studied through the theoretical and experimental methods. Based on the boiling cooling mechanism of LN2, a set of predicted mathematical model considering the evaporating part before impacting, spreading adhesion, and impact spatter abilities was established. The effects of injection velocity and injection angle on the cooling speed, spreading area, and splashing state were analyzed. A series of milling experiments with LN2 impact cooling were executed. The results show that the smaller injection angle can cause a larger temperature difference, as well as achieving the easy nuclear boiling and improving the heat flux. At the same flow, the cooling effect is better at the condition of small milling depth following the smaller injection angle, as well as the excellent cutting quality. At large milling depth, the cooling effect at injection angle αn = 20° is not as good as that of 40°. Meanwhile, the relation between injection angle and feed is similar to that of milling depth. At small LN2 flow, the cooling rate will be less than the required speed at bigger cutting parameter; the processing area of the workpiece cannot be completely cooled, which causes the cooling effect, and cutting quality is not ideal. In addition, the cutting effect at angle αn = 40° is also better at large flow qf = 50 L/h. Furthermore, the smaller injection angle has the larger microhardness, and it is conducive to increase strain rate and rapidly reducing temperature, as well as the degree of high grain refinement. Ultimately, the small LN2 flow is followed small impact speed, the small injection angle 20° has the shortest cooling time with the strong cooling ability, and it is suitable for the cooling processing of small cutting parameters. Under the large flow, the injection angle of 40° can relatively increase the spreading time of LN2 and achieve full boiling heat transfer and can guarantee the complete cooling processing for large cutting parameters.
引用
收藏
页码:1185 / 1201
页数:16
相关论文
共 50 条
  • [31] Effect of cryogenic cooling on machinability and surface quality of bio-degradable ZK60 Mg alloy
    Dinesh, S.
    Senthilkumar, V.
    Asokan, P.
    Arulkirubakaran, D.
    MATERIALS & DESIGN, 2015, 87 : 1030 - 1036
  • [32] Comparison of cryogenic cooling strategy effects on machinability of milling nickel-based alloy
    Wang, Fengbiao
    Wang, Yongqing
    JOURNAL OF MANUFACTURING PROCESSES, 2021, 66 : 623 - 635
  • [33] Comparison of cryogenic cooling strategy effects on machinability of milling nickel-based alloy
    Wang, Fengbiao
    Wang, Yongqing
    Journal of Manufacturing Processes, 2021, 66 : 623 - 635
  • [34] Synthesis of titanium dioxide nanofluid and application in jet impingement cooling in steel industries
    Sarkar, Ishita
    Pal, Surjya
    Chakraborty, Sudipto
    ABSTRACTS OF PAPERS OF THE AMERICAN CHEMICAL SOCIETY, 2017, 254
  • [35] A REVIEW ON COOLING OF DISCRETE HEATED MODULES USING LIQUID JET IMPINGEMENT
    Patil, Naveen G.
    Hotta, Tapano Kumar
    FRONTIERS IN HEAT AND MASS TRANSFER, 2018, 11
  • [36] Submerged Liquid Jet Array Impingement Cooling with High Gravity Effects
    Wang, Z. Y.
    Wong, T. N.
    Duan, F.
    Toh, K. C.
    Choo, K. F.
    Tan, S. P.
    Loh, C. V.
    Leong, Y. W.
    PROCEEDINGS OF THE 2012 IEEE 14TH ELECTRONICS PACKAGING TECHNOLOGY CONFERENCE, 2012, : 511 - 514
  • [37] Modeling-Based Improvement of Microscale Liquid Jet Impingement Cooling
    Elsinger, Georg
    Oprins, Herman
    Cherman, Vladimir
    Van Der Plas, Geert
    Beyne, Eric
    De Wolf, Ingrid
    IEEE TRANSACTIONS ON COMPONENTS PACKAGING AND MANUFACTURING TECHNOLOGY, 2024, 14 (07): : 1180 - 1188
  • [38] Effect of aging plus cryogenic treatment on the machinability of 7075 aluminum alloy
    Zhang, Ping
    Liu, Zehua
    Liu, Junling
    Yu, Jiang
    Mai, Qingqun
    Yue, Xiujie
    VACUUM, 2023, 208
  • [39] Influence of cooling in liquid nitrogen on shape memory effect of CuZnAlMnNi alloy
    Bai, YJ
    Xu, XG
    Hao, XP
    Cui, DL
    Geng, GL
    MATERIALS RESEARCH BULLETIN, 2001, 36 (13-14) : 2415 - 2419
  • [40] Laser-alloying of a titanium alloy with a nitrogen jet
    Medres, B
    Shepeleva, L
    Bamberger, M
    LASERS IN ENGINEERING, 2001, 11 (02) : 143 - 152