A Comparative Study on the Effect of Milling and Abrasive Water Jet Cutting Technologies on the Tensile Behavior of Composite Carbon/Epoxy Laminates

被引：0
作者：
A. Abidi
S. Ben Salem
A. Bezazi
H. Boumediri
机构：
[1] Tunis El Manar University,Laboratory of Applied Mechanics and Engineering (LR
[2] Preparatory Institute of Engineering Mrezka Nabeul (IPEIN),MAI), National School of Engineers of Tunis (ENIT)
[3] Carthage University,Laboratoire de Mécanique Appliquée des Nouveaux Matériaux (LMANM)
[4] Université 8 Mai 1945,undefined
来源：
Mechanics of Composite Materials | 2021年 / 57卷
关键词：
CFRP; high-speed milling; abrasive water jet; tension; cutting process;
D O I：
暂无
中图分类号：
学科分类号：
摘要：
Tensile tests of composite materials based on carbonfiber reinforced plastics (CFRPs) have been performed to benchmark the impact of action of abrasive water jet (AWJ) and high-speed milling (HSM) on the stiffness and strength of CFRP laminates. CFRP specimens were tested according to the ASTM D3039 and ASTM D5766. The drilled specimens exhibited a linear behavior up to failure, but their stress–strain relation was pronouncedly nonlinear, with higher tensile strains than nondrilled ones. Results showed that ultimate the stress–strain relation and Young’s modulus were affected by the machining process. The stress and strain limits for samples prepared using the AWJ method were higher than for those machined by HSM, but the opposite effect was observed for Young’s modulus.
引用
收藏
页码：539 / 550
页数：11
相关论文
共 98 条
[1]  
Haddad M(2014)Study of trimming damages of CFRP structures in function of the machining processes and their impact on the mechanical behavior Composites, Part B 57 136-43
[2]  
Zitoune R(2018)Prediction model of ultimate tensile strength and investigation on microstructural characterization of friction stir welded AA2024-T3 Int. J. Adv. Manuf. Technol. 95 1473-1486
[3]  
Bougherara H(2020)Comparative analysis of wobble milling, helical milling and conventional drilling of CFRPs Int J Adv Manuf Technol 106 3913-3930
[4]  
Eyma F(2019)Advanced cutting tools and technologies for drilling carbon fibre reinforced polymer (CFRP) composites: A review Composites, Part A 125 67-80
[5]  
Castanie B(2020)Analysis of characteristics of surface roughness of machined CFRP composites Periodica Polytechnica Mechanical Engineering 64 2481-2490
[6]  
Boulahem K(2018)Experimental study on hole quality and its impact on tensile behavior following pure and abrasive water jet cutting of plain woven CFRP laminates The International Journal of Advanced Manufacturing Technology 99 169-177
[7]  
Ben Salem S(2013)Investigating the effect of machining processes on the mechanical behavior of composite plates with circular holes Composites, Part A 55 2261-2272
[8]  
Bessrour J(2009)Effect of fiber orientation on nonlinear behavior of CFRP Composites Journal of Reinforced Plastics and Composites 8 243-256
[9]  
Pereszlai C(2006)Off-axis fatigue behavior of plain weave carbon/epoxy fabric laminates at room and high temperatures and its mechanical modeling Composites, Part A 37 545-576
[10]  
Geier N(2001)Off-axis fatigue behavior of unidirectional carbon fiber-reinforced composites at room and high temperatures J. Compos. Mater. 35 3139-3154
12345678910