Introduction of a new bar-rolling mill

被引：0
|
作者：
Viventsov A.S. [1 ]
Kaskin B.K. [1 ]
Vdovin S.V. [1 ]
Serdyukov O.V. [1 ]
Kutuzov V.V. [1 ]
机构：
[1] AO ArcelorMittal Temirtau, Temirtau
来源：
Steel in Translation | 2010年 / 40卷 / 06期
关键词：
Austenite; Pearlite; State Standard GOST; Strength Class; Complex Profile;
D O I：
10.3103/S096709121006015X
中图分类号：
学科分类号：
摘要：
An up-to-date bar-rolling shop has gone into operation at AO ArcelorMittal Temirtau. The production of rolled bar and complex profiles, including the rolling and splitting of rebar profiles 8, 10, 12, and 14, has been successfully introduced. The rolling mill is equipped with a Thermex system for heat treatment of the profiles (thermomechanical strengthening). Optimal rolling and heat-treatment conditions are established for rebar produced from imported CT3cΠ and CT3cΠ steel billet. The products fully comply with strength class At400 according to State Standard GOST 10884-94. © 2010 Allerton Press, Inc.
引用
收藏
页码：574 / 576
页数：2
相关论文
共 14 条
  • [1] Production of thermally strengthened rod reinforcement on OAO ZSMK bar-rolling mills
    Galiullin T.R.
    Chinokalov V.Ya.
    Poltoratskii L.M.
    Steel in Translation, 2007, 37 (10) : 886 - 888
  • [2] Assessing channel rolling on a 450 mill
    Nazarov D.V.
    Zakharov E.A.
    Denisov S.V.
    Moller A.B.
    Zav'yalov K.A.
    Steel in Translation, 2009, 39 (10) : 901 - 905
  • [3] An Online Rolling Model for Plate Mill Using Parallel Computation
    Otsuka, Takayuki
    Sakamoto, Masashi
    Takamachi, Yasuyuki
    Higashida, Yasuhiro
    Segawa, Yuji
    Takeshima, Shohta
    ISIJ INTERNATIONAL, 2017, 57 (11) : 2042 - 2048
  • [4] An Online Rolling Model for Plate Mill Using Parallel Computation
    Otsuka, Takayuki
    Sakamoto, Masashi
    Takamachi, Yasuyuki
    Higashida, Yasuhiro
    Segawa, Yuji
    Takeshima, Shohta
    TETSU TO HAGANE-JOURNAL OF THE IRON AND STEEL INSTITUTE OF JAPAN, 2019, 105 (08): : 46 - 52
  • [5] Section for the thermal hardening of reinforcement in the casting and rolling system of the 280 mill
    Lipunov Y.I.
    Eismondt K.Y.
    Myagkov K.A.
    Rzhevitskii S.N.
    Klopov V.I.
    Dunaev V.A.
    Starikov E.V.
    Steel in Translation, 2010, 40 (3) : 285 - 289
  • [6] Development and introduction of the hot-plate mill program
    Yu. D. Makarov
    I. V. Nedorezov
    E. G. Beloglazov
    A. M. Stepashin
    E. V. Yakushev
    Ya. M. Fel’dman
    A. P. Mal’tsev
    Metallurgist, 2007, 51 : 172 - 175
  • [7] Development and introduction of the hot-plate mill program
    Makarov, Yn. D.
    Nedorezov, I. V.
    Beloglazov, E. G.
    Stepashin, A. M.
    Yakushev, E. V.
    Fel'dman, Ya. M.
    Mal'tsev, A. P.
    METALLURGIST, 2007, 51 (3-4) : 172 - 175
  • [8] THE STUDY OF THE QUALITY OF HOT THIN BEAMS OBTAINED BY ROLLING ON A LONGITUDINAL WEDGE MILL
    Mashekov, S. A.
    Kiyanbekova, L. R.
    Alshynova, A. M.
    Mashekova, A. S.
    Smailova, G. A.
    Urazbaeva, R. E.
    Tussupkaliyeva, E. A.
    NEWS OF THE NATIONAL ACADEMY OF SCIENCES OF THE REPUBLIC OF KAZAKHSTAN-SERIES OF GEOLOGY AND TECHNICAL SCIENCES, 2018, (06): : 23 - 36
  • [9] Microalloying Precipitation during Hot Rolling of Seamless Tubes in a Continuous Mandrel Mill
    Carvalho, Ricardo N.
    Ferreira, Marcelo A. C.
    Lima, Marilia M.
    Santos, Dagoberto B.
    Barbosa, Ronaldo
    STEEL RESEARCH INTERNATIONAL, 2019, 90 (02)
  • [10] Development of rolling procedures for pipes of K55 strength class at the laboratorial mill
    Adigamov, R. R.
    Baraboshkin, K. A.
    Mishnev, P. A.
    Karlina, A. I.
    CIS IRON AND STEEL REVIEW, 2022, 24 : 60 - 66
12