Minimum entropy generation for laminar flow at constant wall temperature in a circular duct for optimum design

被引：0
作者：
Alper Yilmaz
机构：
[1] University of Çukurova,Department of Mechanical Engineering, Faculty of Engineering and Architecture
来源：
Heat and Mass Transfer | 2009年 / 45卷
关键词：
Pressure Loss; Entropy Generation; Total Pressure Loss; Entropy Generation Rate; Constant Wall Temperature;
D O I：
暂无
中图分类号：
学科分类号：
摘要：
Entropy generation for hydrodynamically and thermally developing laminar flow in a circular duct at constant wall temperature is investigated. Optimum temperature difference between fluid inlet temperature and wall temperature is determined for minimum entropy generation rate. An equation for optimum temperature difference at minimum entropy generation rate is given. It is seen that the optimum dimensionless temperature difference is a finite value for a duct length approaching zero for low temperature differences. It is possible to calculate the optimum pressure loss for given wall and inlet fluid temperature differences and corresponding optimum dimensions of a circular duct can be determined with these results. An example for the dimensioning of an air-conditioning heat exchanger tube for given wall and air inlet temperatures and heat transferred is presented.
引用
收藏
页码：1415 / 1421
页数：6
相关论文
共 50 条
[31]   NUMERICAL INVESTIGATION OF ENTROPY GENERATION IN LAMINAR FORCED CONVECTION FLOW OVER INCLINED BACKWARD AND FORWARD FACING STEPS IN A DUCT UNDER BLEEDING CONDITION [J].
Atashafrooz, Meysam ;
Gandjalikhan Nassaj, Seyyed Abdolreza ;
Ansari, Amir Babak .
THERMAL SCIENCE, 2014, 18 (02) :479-492
[32]   Optimal heating strategy for minimization of peak temperature and entropy generation for forced convective flow through a circular pipe [J].
Pati, Sukumar ;
Roy, Rajib ;
Deka, Nabajit ;
Boruah, Manash Protim ;
Nath, Mriganka ;
Bhargav, Ritwick ;
Randive, Pitambar R. ;
Mukherjee, Partha P. .
INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER, 2020, 150
[33]   Entropy generation for flow boiling on a single semi-circular minichannel [J].
See, Y. S. ;
Leong, K. C. .
INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER, 2020, 154
[34]   Second law analysis of compressible flow through a diffuser subjected to constant wall temperature [J].
Arshad, Mohammad Hasan ;
Kahraman, Ramazan ;
Sahin, Ahmet Z. ;
Mansour, Rached Ben .
INTERNATIONAL JOURNAL OF EXERGY, 2010, 7 (01) :110-129
[35]   Optimum slip flow based on the minimization of entropy generation in parallel plate microchannels [J].
Ibanez, Guillermo ;
Lopez, Aracely ;
Pantoja, Joel ;
Moreira, Joel ;
Reyes, Juan A. .
ENERGY, 2013, 50 :143-149
[36]   Entropy Generation in Laminar Forced Convective Water Flow Due to Overloading Toward the Microscale [J].
Rastogi, Pallavi ;
Mahulikar, Shripad P. .
JOURNAL OF ENERGY RESOURCES TECHNOLOGY-TRANSACTIONS OF THE ASME, 2018, 140 (08)
[37]   Entropy Generation and Poiseuille Number Link in Developing Isothermal Laminar Micro-Flow [J].
Rastogi, Pallavi ;
Mahulikar, Shripad P. .
JOURNAL OF ENERGY RESOURCES TECHNOLOGY-TRANSACTIONS OF THE ASME, 2022, 144 (04)
[38]   Numerical Investigation of Local Entropy Generation for Laminar Flow in Rotating-Disk Systems [J].
Shanbghazani, Mohammad ;
Heidarpoor, Vahid ;
Rosen, Marc A. ;
Mirzaee, Iraj .
JOURNAL OF HEAT TRANSFER-TRANSACTIONS OF THE ASME, 2010, 132 (09) :1-7
[39]   A numerical study on entropy generation and optimization. for laminar forced convection in a rectangular curved duct with longitudinal ribs [J].
Ko, T. -H. .
INTERNATIONAL JOURNAL OF THERMAL SCIENCES, 2006, 45 (11) :1113-1125
[40]   Entropy generation analysis of fully developed turbulent convection in a twisted elliptical duct with constant heat flux [J].
Cheng, Junlin ;
Wang, Zizhao ;
Mao, Huiyi .
INTERNATIONAL JOURNAL OF EXERGY, 2023, 41 (02) :131-141
12345