Minimum entropy generation for laminar flow at constant wall temperature in a circular duct for optimum design

被引：0
作者：
Alper Yilmaz
机构：
[1] University of Çukurova,Department of Mechanical Engineering, Faculty of Engineering and Architecture
来源：
Heat and Mass Transfer | 2009年 / 45卷
关键词：
Pressure Loss; Entropy Generation; Total Pressure Loss; Entropy Generation Rate; Constant Wall Temperature;
D O I：
暂无
中图分类号：
学科分类号：
摘要：
Entropy generation for hydrodynamically and thermally developing laminar flow in a circular duct at constant wall temperature is investigated. Optimum temperature difference between fluid inlet temperature and wall temperature is determined for minimum entropy generation rate. An equation for optimum temperature difference at minimum entropy generation rate is given. It is seen that the optimum dimensionless temperature difference is a finite value for a duct length approaching zero for low temperature differences. It is possible to calculate the optimum pressure loss for given wall and inlet fluid temperature differences and corresponding optimum dimensions of a circular duct can be determined with these results. An example for the dimensioning of an air-conditioning heat exchanger tube for given wall and air inlet temperatures and heat transferred is presented.
引用
收藏
页码：1415 / 1421
页数：6
相关论文
共 50 条
[21]   A numerical investigation of entropy generation in the entrance region of curved pipes at constant wall temperature [J].
Amani, E. ;
Nobari, M. R. H. .
ENERGY, 2011, 36 (08) :4909-4918
[22]   Laminar Heat Transfer for Gas-Liquid Segmented Flows in Circular and Non-circular Ducts with Constant Wall Temperature [J].
Muzychka, Y. S. .
PROCEEDINGS OF THE ASME 12TH INTERNATIONAL CONFERENCE ON NANOCHANNELS, MICROCHANNELS, AND MINICHANNELS, 2014, 2014,
[23]   Numerical investigation on laminar forced convection and entropy generation in a curved rectangular duct with longitudinal ribs mounted on heated wall [J].
Ko, TH .
INTERNATIONAL JOURNAL OF THERMAL SCIENCES, 2006, 45 (04) :390-404
[24]   Entropy generation in viscous flow due to generalized exponential wall velocity and temperature [J].
Hussain, M. ;
Mehmood, A. ;
Usman, M. .
PHYSICA SCRIPTA, 2023, 98 (07)
[25]   Optimum wall thickness ratio based on the minimization of entropy generation in a viscous flow between parallel plates [J].
Ibanez, Guillermo ;
Lopez, Aracely ;
Cuevas, Sergio .
INTERNATIONAL COMMUNICATIONS IN HEAT AND MASS TRANSFER, 2012, 39 (05) :587-592
[26]   Experimental study of heat transfer in rarefied gas flow in a circular tube with constant wall temperature [J].
Hemadri, Vadiraj ;
Biradar, G. S. ;
Shah, Nishant ;
Garg, Richie ;
Bhandarkar, U. V. ;
Agrawal, Amit .
EXPERIMENTAL THERMAL AND FLUID SCIENCE, 2018, 93 :326-333
[27]   Entropy Generation Analysis of Nanofluid Flow in Turbulent and Laminar Regimes [J].
Moghaddami, Mostafa ;
Shahidi, Seyedehsan ;
Siavashi, Majid .
JOURNAL OF COMPUTATIONAL AND THEORETICAL NANOSCIENCE, 2012, 9 (10) :1586-1595
[28]   Entropy Generation Analysis for Various Cross-sectional Ducts in Fully Developed Laminar Convection with Constant Wall Heat Flux [J].
Haghgooyan, M. S. ;
Aghanajafi, C. .
KOREAN CHEMICAL ENGINEERING RESEARCH, 2014, 52 (03) :294-301
[29]   Investigation of entropy generation in nanofluid's axisymmetric stagnation flow over a cylinder with constant wall temperature and uniform surface suction-blowing [J].
Zahmatkesh, R. ;
Mohammadiun, H. ;
Mohammadiun, M. ;
Bonab, M. H. Dibaei .
ALEXANDRIA ENGINEERING JOURNAL, 2019, 58 (04) :1483-1498
[30]   Optimum wall conductance ratio in magnetoconvective flow in a long vertical rectangular duct [J].
Ibanez, Guillermo ;
Cuevas, Sergio .
INTERNATIONAL JOURNAL OF THERMAL SCIENCES, 2008, 47 (08) :1012-1019
12345