Influence of the drawing angle on wire quality

被引：1
|
作者：
Gur’yanov G.N. [1 ]
Zhelezkov O.S. [1 ]
Platov S.I. [1 ]
Terent’ev D.V. [1 ]
机构：
[1] Nosov Magnitogorsk State Technical University, Magnitogorsk
来源：
Steel in Translation | 2015年 / 45卷 / 01期
关键词：
axial stress; die collar; drawing; energy economy; margin of safety; optimal drawing angle; wire;
D O I：
10.3103/S0967091215010076
中图分类号：
学科分类号：
摘要：
The axial stress, absolute margin of safety, and Perlin’s safety factor of wire are calculated, and assessment of the shaping efficiency in drawing round nonhollow wire is discussed. With optimal drawing angle, when the axial stress is minimal, maximum margin of safety and shaping efficiency will be observed. © 2015, Allerton Press, Inc.
引用
收藏
页码：18 / 24
页数：6
相关论文
共 50 条
  • [1] OPTIMUM DIE ANGLE IN FAST WIRE DRAWING
    CRISTESCU, N
    JOURNAL OF MECHANICAL WORKING TECHNOLOGY, 1980, 3 (3-4): : 275 - 287
  • [2] EFFECT OF DRAWING ANGLE SIZE OF A DIE ON WIRE DRAWING AND BUNCHING PROCESS
    Tittel, Viktor
    Zelenay, Miroslav
    Kudelas, Lubos
    21ST INTERNATIONAL CONFERENCE ON METALLURGY AND MATERIALS (METAL 2012), 2012, : 361 - 367
  • [3] EFFECT OF DIE ANGLE ON THE WIRE DRAWING PROCESS.
    Bhattacharyya, A.
    Chakraborty, A.C.
    Deb, S.R.
    Mullick, B.K.
    Annals of the CIRP, 1972, 21 (01): : 59 - 60
  • [4] The Influence of Temperature in the Wire Drawing Process on the Wear of Drawing Dies
    Suliga, Maciej
    Szota, Piotr
    Gwozdzik, Monika
    Kulasa, Joanna
    Brudny, Anna
    MATERIALS, 2024, 17 (20)
  • [5] Influence of process parameters in drawing of superconducting wire
    Malberg, M
    Bech, J
    Bay, N
    Skov-Hansen, P
    Cualbu, G
    IEEE TRANSACTIONS ON APPLIED SUPERCONDUCTIVITY, 1999, 9 (02) : 2577 - 2580
  • [6] Influence of process parameters in drawing of superconducting wire
    Malberg, M.
    Bech, J.
    Bay, N.
    Skov-Hansen, P.
    Cualbu, G.
    IEEE Transactions on Applied Superconductivity, 1999, 9 (2 II): : 2577 - 2580
  • [7] INFLUENCE OF DRAWING SPEED ON DRAWING FORCE AND MECHANICAL-PROPERTIES OF STEEL WIRE
    VOLLMER, H
    PAWELSKI, O
    STAHL UND EISEN, 1976, 96 (08): : 392 - 397
  • [8] In-line quality control of fine wire drawing
    Jakob, Klaus
    Kraft, Michael
    Wire, 1996, 46 (04): : 241 - 242
  • [9] Rational distribution of the working angle of dies during continuous wire drawing
    Zykov, YS
    STEEL IN TRANSLATION, 1997, 27 (02) : 52 - 54
  • [10] Wire Drawing Behaviors with Die Angle and Strain Hardening Rate of a Metal
    Hwang, Joong-Ki
    JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE, 2025, 34 (02) : 1207 - 1214
12345