Increasing punch life in cold cup extrusion with active friction

被引：1

作者：

Dmitriev M. ^{[1
]}

Korobova N.V. ^{[1
]}

Yakubovskaya I.A. ^{[1
]}

机构：

[1] Stankin Moscow State Technological University, Moscow

来源：

Russian Engineering Research | 2015年 / 35卷 / 12期

关键词：

blank; cold extrusion; metal cups; modeling; punch life; resistance; stress;

D O I：

10.3103/S1068798X15120060

中图分类号：

学科分类号：

摘要：

The stress at the end surface of the punch in the cold extrusion of a U-shaped hollow cylinder (a cup) is determined by modeling with regression equations. The results of such extrusion with active and reactive friction at blank–matrix contact are compared. With active friction, the punch life is greater by a factor of 1.5. © 2015, Allerton Press, Inc.

引用

页码：896 / 901

页数：5

共 14 条

[1]

Dmitriev A.M., Korobova N.V., Expanding of application of cold die forging by inducing active contact friction forces, J. Frict. Wear, 34, pp. 232-237, (2013)

[2]

Dmitriev A.M., Grigoriev S.N., Korobova N.V., Stupnikov V.P., A study of the quality of preforms from iron-base powders produced by forming combined with sintering by electric current pulses, Metal Sci. Heat Treat., 54, pp. 17-21, (2012)

[3]

Dmitriev A.M., Vorontsov A.L., Determination of the parameters of constrained extrusion of hollow cylindrical articles, Kuzn.-Shtamp. Proizv., 12, pp. 17-21, (2004)

[4]

Dmitriev A.M., Vorontsov A.L., Examples of determination of technological parameters of extruding thimbles from strengthening materials, Kuzn.-Shtamp. Proizv., 11, pp. 21-28, (2004)

[5]

Dmitriev A.M., Dubrovskii V.A., Stupnikov V.P., Scientific session on problems of billet quality provision in machine-building industry, Probl. Mashinostr. Nadezhn. Mash., 3, pp. 121-124, (2004)

[6]

Dmitriev A.M., Vorontsov A.L., Optimization of the processes of cold forming by reduction, Kuzn.Shtamp. Proizv., 5, pp. 3-7, (2003)

[7]

Dmitriev A.M., Vorontsov A.L., Approximation of metal hardening curves, Kuzn.-Shtamp. Proizv., 6, pp. 16-21, (2002)

[8]

Dmitriev A.M., Grechnikov F.V., Korobova N.V., Tolmachev N.S., Practical use of the change in mechanical characteristics of structural carbon steel in cold bulk stamping, Vestn. MGTU Stankin, 4, 31, pp. 41-44, (2014)

[9]

Dmitriev A.M., Korobova N.V., Tolmachev N.S., Experimental verification of the computer simulation of the stress on a deforming tool, Vestn. MGTU Stankin, 2, 29, pp. 44-49, (2014)

[10]

Sosenushkin E.N., Ponomarev A.S., Artes A.E., Klimov V.N., Influence of pressure treatment on the microstructure and quality of high-strength cast-iron parts, Vestn. MGTU Stankin, 3, 15, pp. 115-120, (2011)

← 1 2 →