Influence of Wear on the Cross-Coupled Dynamic Coefficients and Threshold Speed of Conical Hybrid Fluid Film Bearing

被引：0
作者：
Pawar S.R. [1 ]
Phalle V.M. [2 ]
Sawant P.K. [1 ]
机构：
[1] Department of Mechanical Engineering, Bharati Vidyapeeth College of Engineering, Navi Mumbai
[2] Department of Mechanical Engineering, VJTI, H.R. Mahajani Marg, Matunga, Mumbai
来源：
J. Inst. Eng. Ser. C | 2250年 / 6卷 / 1173-1180期
关键词：
Conical; Damping; Hybrid; Stiffness; Threshold speed; Wear;
D O I：
10.1007/s40032-023-01000-4
中图分类号：
学科分类号：
摘要：
Hybrid journal bearings are used mostly to take benefits of simultaneous hydrostatic and hydrodynamic actions. This paper uses numerical technique to investigate wear effect on the cross-coupled dynamic coeff. and threshold stability speed of recessless conical hybrid journal bearing (CHJB) using capillary restrictor. The developed Reynolds equation describing the streamline incompressible flow, iso-viscous lubricating fluid in the narrow region of conical bearing and journal is resolved by methodology of finite element. Results obtained by numerical simulation reveal the considerable change in the dynamic coeff. and threshold stability speed of worn CHJB as compared to newly installed bearing of matching configuration. © 2023, The Institution of Engineers (India).
引用
收藏
页码：1173 / 1180
页数：7
相关论文
共 10 条
  • [1] Stout K.J., Rowe W.B., Externally pressurised design for manufacture: part 1 journal bearing selection, Tribol. Int., 7, 3, pp. 98-106, (1974)
  • [2] Prabhu J.T., Ganesan N., Characteristics of conical hydrostatic thrust bearings under rotation, Wear, 73, 1, pp. 95-122, (1981)
  • [3] Prabhu J.T., Ganesan N., Analysis of multirecess conical hydrostatic thrust bearings under rotation, Wear, 89, 1, pp. 29-40, (1983)
  • [4] Rowe W.B., Xu S.X., Hybrid journal bearing with particular reference to hole-entry configuration, Tribol. Int., 15, 6, pp. 339-348, (1982)
  • [5] Dufrane K.F., Kannel J.W., McCloskey T.H., Wear of steam turbine journal bearings at low operating speeds, J. Lubric. Technol., 105, pp. 313-317, (1983)
  • [6] Yoshimoto S., Rowe W.B., A Theoretical investigation of the effect of inlet pocket-size on the performance of hole-entry hybrid journal bearing employing capillary restrictors, Wear, 127, 3, pp. 307-318, (1988)
  • [7] Fillon M., Bouyer J.I., Influence of wear on the behaviour of a two-lobe hydrostatic journal bearing subjected to numerous start-ups and stops, ASME J. Tribol., 129, pp. 205-208, (2007)
  • [8] Awasthi R.K., Sharma S.C., Jain S.C., Effect of wear on the performance of non-recessed orifice compensated hybrid journal bearing, Tribol. Trans., 50, 3, pp. 361-373, (2007)
  • [9] Sharma S.C., Phalle V.M., Jain S.C., Influence of Wear on the performance of a multirecess conical hybrid journal bearing compensated with orifice restrictor, Tribol. Int., 44, 12, pp. 1754-1764, (2011)
  • [10] Khakse P.G., Phalle V.M., Mantha S.S., Performance analysis of a non-recessed hybrid conical journal bearing compensated with capillary restrictors, ASME J. Tribol., 138, 1, pp. 011703-11709, (2016)
1