Wear Behavior of Harmonic Structured 304L Stainless Steel

被引：14

作者：

Rai, Prabhat K. ^{[1
]}

Shekhar, S. ^{[1
]}

Nakatani, M. ^{[2
]}

Ota, M. ^{[4
]}

Vajpai, S. K. ^{[3
]}

Ameyama, K. ^{[4
]}

Mondal, K. ^{[1
]}

机构：

[1] Indian Inst Technol Kanpur, Dept Mat Sci & Engn, Kanpur 208016, Uttar Pradesh, India

[2] Ritsumeikan Univ, Grad Sch Sci & Engn, Kusatsu, Shiga 5258577, Japan

[3] Ritsumeikan Univ, Res Org Sci & Technol, Kusatsu, Shiga 5258577, Japan

[4] Ritsumeikan Univ, Fac Sci & Engn, Kusatsu, Shiga 5258577, Japan

来源：

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE | 2017年 / 26卷 / 06期

关键词：

friction; harmonic structure; steel; wear; MECHANICAL-PROPERTIES; FRETTING WEAR; PLASTIC-DEFORMATION; STRUCTURE DESIGN; NANOCRYSTALLINE; COPPER; MICROSTRUCTURE; PERFORMANCE; DUCTILITY; SURFACE;

D O I：

10.1007/s11665-017-2719-2

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

Wear behavior of a harmonic structured 304L austenitic stainless steel with periodically distributed fine and coarse grains was examined and compared with a sintered non-harmonic structured 304L stainless steel and a low carbon conventional 304 stainless steel using fretting wear tests at varying loads in ball-on-flat contact configuration. Characterization was accomplished using scanning electron microscope, energy-dispersive spectroscopy, optical profilometry and Raman spectroscopy. Coefficient of friction and wear volume were minimum at intermediate normal load of 5 N, whereas maximum at 10 N for the harmonic stainless steel compared to other two steels. Harmonically distributed fine-and coarse-grained structure attributes to the higher wear rate of the harmonic structured steel at higher load because of differential interaction of the ball with the harmonically distributed hard (fine) and relatively soft (coarse) regions.

引用

页码：2608 / 2618

页数：11

共 50 条

[31] Phase transformations in cold-rolled 304L stainless steel by dilatometry [J].

Bachani, Mokded ;

Hayoune, Abdelali ;

Fajoui, Jamal ;

Dubos, Pierre-Antoine .

BULLETIN OF MATERIALS SCIENCE, 2024, 47 (02)

[32] Parametric study of transient temperature distribution in FSW of 304L stainless steel [J].

Chansoria, P. ;

Solanki, P. ;

Dasgupta, M. S. .

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2015, 80 (5-8) :1223-1239

[33] Effect of SLM Build Parameters on the Compressive Properties of 304L Stainless Steel [J].

Fashanu, Okanmisope ;

Buchely, Mario E. ;

Spratt, Myranda ;

Newkirk, Joseph ;

Chandrashekhara, K. ;

Misak, Heath ;

Walker, Michael .

JOURNAL OF MANUFACTURING AND MATERIALS PROCESSING, 2019, 3 (02)

[34] Improvement of the corrosion behavior of AISI 304L stainless steel by deep rolling treatment under cryogenic cooling [J].

Gharbi, Khouloud ;

Ben Moussa, Naoufel ;

Ben Rhouma, Amir ;

Ben Fredj, Nabil .

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2021, 117 (11-12) :3841-3857

[35] Mechanical properties of Austenitic Stainless Steel 304L and 316L at elevated temperatures [J].

Desu, Raghuram Karthik ;

Krishnamurthy, Hansoge Nitin ;

Balu, Aditya ;

Gupta, Amit Kumar ;

Singh, Swadesh Kumar .

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T, 2016, 5 (01) :13-20

[36] Hardening behavior of selective laser melted 304L stainless steel under Xe irradiation [J].

Li, Ying ;

Li, Jianjian ;

Fu, Chonglong ;

Bai, Juju ;

Hou, Juan ;

Lin, Jun ;

Dai, Zhimin .

VACUUM, 2021, 192

[37] Fatigue behavior and modeling for additive manufactured 304L stainless steel: The effect of surface roughness [J].

Lee, Seungjong ;

Pegues, Jonathan W. ;

Shamsaei, Nima .

INTERNATIONAL JOURNAL OF FATIGUE, 2020, 141

[38] Microstructure and corrosion behavior of multipass gas tungsten arc welded 304L stainless steel [J].

Mirshekari, G. R. ;

Tavakoli, E. ;

Atapour, M. ;

Sadeghian, B. .

MATERIALS & DESIGN, 2014, 55 :905-911

[39] Fatigue and tensile deformation behaviors of laser powder bed fused 304L austenitic stainless steel [J].

Zhang, Hongzhuang ;

Li, Changyou ;

Shi, Yanlin ;

Yao, Guo ;

Zhang, Yimin .

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2022, 849

[40] Effect of SiC particle impact nano-texturing on tribological performance of 304L stainless steel [J].

Lorenzo-Martin, C. ;

Ajayi, O. O. .

APPLIED SURFACE SCIENCE, 2014, 315 :287-291

← 1 2 3 4 5 →