Wear Behavior of Harmonic Structured 304L Stainless Steel

被引:14
作者
Rai, Prabhat K. [1 ]
Shekhar, S. [1 ]
Nakatani, M. [2 ]
Ota, M. [4 ]
Vajpai, S. K. [3 ]
Ameyama, K. [4 ]
Mondal, K. [1 ]
机构
[1] Indian Inst Technol Kanpur, Dept Mat Sci & Engn, Kanpur 208016, Uttar Pradesh, India
[2] Ritsumeikan Univ, Grad Sch Sci & Engn, Kusatsu, Shiga 5258577, Japan
[3] Ritsumeikan Univ, Res Org Sci & Technol, Kusatsu, Shiga 5258577, Japan
[4] Ritsumeikan Univ, Fac Sci & Engn, Kusatsu, Shiga 5258577, Japan
关键词
friction; harmonic structure; steel; wear; MECHANICAL-PROPERTIES; FRETTING WEAR; PLASTIC-DEFORMATION; STRUCTURE DESIGN; NANOCRYSTALLINE; COPPER; MICROSTRUCTURE; PERFORMANCE; DUCTILITY; SURFACE;
D O I
10.1007/s11665-017-2719-2
中图分类号
T [工业技术];
学科分类号
08 ;
摘要
Wear behavior of a harmonic structured 304L austenitic stainless steel with periodically distributed fine and coarse grains was examined and compared with a sintered non-harmonic structured 304L stainless steel and a low carbon conventional 304 stainless steel using fretting wear tests at varying loads in ball-on-flat contact configuration. Characterization was accomplished using scanning electron microscope, energy-dispersive spectroscopy, optical profilometry and Raman spectroscopy. Coefficient of friction and wear volume were minimum at intermediate normal load of 5 N, whereas maximum at 10 N for the harmonic stainless steel compared to other two steels. Harmonically distributed fine-and coarse-grained structure attributes to the higher wear rate of the harmonic structured steel at higher load because of differential interaction of the ball with the harmonically distributed hard (fine) and relatively soft (coarse) regions.
引用
收藏
页码:2608 / 2618
页数:11
相关论文
共 50 条
[11]   Temperature dependence of energy dissipation during nanoscale wear of AISI 304L stainless steel [J].
Liu, Yi ;
Bai, Liuyang ;
Pham, Sang T. ;
Wang, Jianli ;
Wan, Shanhong .
WEAR, 2024, 538
[12]   Electrochemical Corrosion Behavior of Explosively Welded Ti/Type 304L Stainless Steel in Nitric Acid [J].
Ghosal, Amrita Mahanti ;
Chandra, Kamlesh ;
Kain, Vivekanand .
CORROSION, 2022, 78 (08) :726-739
[13]   Corrosion and wear behavior of TiN PVD coated 304 stainless-steel [J].
Awan, Awais ;
Pasha, Riffat Asim ;
Butt, Muhammad Shoaib ;
Malik, Rizwan Ahmed ;
Alarifi, Ibrahim M. ;
Alzaid, Meshal ;
Latif, Muhammad ;
Naseer, Ammar ;
Saleem, Mohsin ;
Alrobei, Hussein .
JOURNAL OF MECHANICAL SCIENCE AND TECHNOLOGY, 2020, 34 (08) :3227-3232
[14]   Study of surface appearance and composition effect on AISI 304 and 304L stainless steel wear against nylon wire [J].
Chattrakul, Kawita ;
Sornsuwit, Nuttaphong .
MATERIALS TODAY-PROCEEDINGS, 2018, 5 (03) :9319-9325
[15]   On the tribocorrosion behavior of 304L stainless steel in olive pomace/tap water filtrate [J].
Ben Saada, Fatma ;
Antar, Zied ;
Elleuch, Khaled ;
Ponthiaux, Pierre .
WEAR, 2015, 328 :509-517
[16]   Corrosion Resistance Behavior of GTAW Welded AISI type 304L Stainless Steel [J].
Shit, Gopinath ;
Kuppusamy, M. V. ;
Ningshen, S. .
TRANSACTIONS OF THE INDIAN INSTITUTE OF METALS, 2019, 72 (12) :2981-2995
[17]   Annealing behavior of a 304L stainless steel processed by large strain cold and warm rolling [J].
Odnobokova, Marina ;
Belyakov, Andrey ;
Enikeev, Nariman ;
Molodov, Dmitri A. ;
Kaibyshev, Rustam .
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2017, 689 :370-383
[18]   On the effect of salt bath nitrocarburizing on the cavitation erosion behavior of AISI 304L stainless steel [J].
Markanday, Himanshu ;
Roy, Samir Chandra ;
Somers, Marcel A. J. .
ENGINEERING FAILURE ANALYSIS, 2024, 165
[19]   High-power ultrasonic spot welding of copper to type 304L austenitic stainless steel [J].
Wahba, Mohamed ;
Shamsah, Sami M. Ibn ;
Gepreel, Mohamed A. H. ;
Takahashi, Macoto .
WELDING IN THE WORLD, 2025, 69 (02) :555-569
[20]   Effects of DC plasma nitriding parameters on microstructure and properties of 304L stainless steel [J].
Wang, Jun ;
Xiong, Ji ;
Peng, Qian ;
Fan, Hongyuan ;
Wang, Ying ;
Li, Guijiang ;
Shen, Baoluo .
MATERIALS CHARACTERIZATION, 2009, 60 (03) :197-203