In situ Al3Ti/Al composites fabricated by high shear technology: microstructure and mechanical properties

被引：10

作者：

Zeng, Yan ^{[1
]}

Himmler, David ^{[1
]}

Randelzhofer, Peter ^{[1
]}

Korner, Carolin ^{[1
]}

机构：

[1] Friedrich Alexander Univ Erlangen Nurnberg, Mat Sci & Engn Met, Erlangen, Germany

来源：

MATERIALS SCIENCE AND TECHNOLOGY | 2019年 / 35卷 / 18期

关键词：

Aluminium matrix composites; high shear technology; intermetallic Al3Ti; Ti powder size; SOLID TI POWDERS; TOUGHNESS; PARTICLES; ALUMINUM; MELT; ALLOYS;

D O I：

10.1080/02670836.2019.1677025

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

In situ Al3Ti/Al composites were produced by the reaction between Ti powder and Al melt with high shear technology. As Ti powder is starting material, it is important to investigate its size effect on the microstructure and mechanical properties of Al3Ti/Al composites. The results indicate that the necessary reaction time increases with increasing Ti particle diameter, which results in the Al3Ti phase coarsening. Particle sedimentation occurs at a short mixing time applying large Ti powder. Due to the presence of stiff Al3Ti particles, Young's modulus increases with particle volume fraction and fit well with the predicted values from the Halpin?Tsai equation. Moreover, together with grain refinement, these Al3Ti particles with a homogeneous distribution also lead to an increase in tensile strength.

引用

页码：2294 / 2303

页数：10

共 30 条

[1] Pre-treatment process of B4C particles to improve incorporation into molten AA2014 alloy [J].

Canakci, Aykut ;

Arslan, Fazli ;

Yasar, Ibrahim .

JOURNAL OF MATERIALS SCIENCE, 2007, 42 (23) :9536-9542

[2] ON PLASTIC RELAXATION OF THERMAL-STRESSES IN REINFORCED METALS [J].

DUNAND, DC ;

MORTENSEN, A .

ACTA METALLURGICA ET MATERIALIA, 1991, 39 (02) :127-139

[3] A new technology for treating liquid metals with intensive melt shearing [J].

Fan, Z. ;

Zuo, Y. B. ;

Jiang, B. .

LIGHT METALS TECHNOLOGY V, 2011, 690 :141-144

[4] EFFECT OF GRAIN-SIZE AND STRAIN ON TENSILE FLOW-STRESS OF ALUMINUM AT ROOM-TEMPERATURE [J].

HANSEN, N .

ACTA METALLURGICA, 1977, 25 (08) :863-869

[5] Uniting Strength and Toughness of Al Matrix Composites with Coordinated Al3Ni and Al3Ti Reinforcements [J].

Heim, Frederick M. ;

Zhang, Yunya ;

Li, Xiaodong .

ADVANCED ENGINEERING MATERIALS, 2018, 20 (01)

[6]

Hull D., 2007, An Introduction to Composite Materials, V2nd

[7] Enhanced deformation mechanisms by anisotropic plasticity in polycrystalline Mg alloys at room temperature [J].

Koike, J .

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE, 2005, 36A (07) :1689-1696

[8] Formation of Small Blocky Al3Ti Particles via Direct Reaction Between Solid Ti Powders and Liquid Al [J].

Liu, Z. W. ;

Han, Q. ;

Li, J. G. .

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE, 2012, 43A (12) :4460-4463

[9] Fabrication of in situ Al3Ti/Al composites by using ultrasound assisted direct reaction between solid Ti powders and liquid Al [J].

Liu, Zhiwei ;

Han, Qingyou ;

Li, Jianguo .

POWDER TECHNOLOGY, 2013, 247 :55-59

[10] Development of high-performance A356/nano-Al2O3 composites [J].

Mazahery, A. ;

Abdizadeh, H. ;

Baharvandi, H. R. .

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2009, 518 (1-2) :61-64

← 1 2 3 →