Drilling of CFRP-Ti6Al4V stacks using CO2-cryogenic cooling

被引：72
|
作者：
Rodriguez, A. [1 ]
Calleja, A. [2 ]
de Lacalle, L. N. Lopez [1 ,2 ]
Pereira, O. [1 ]
Rubio-Mateos, A. [3 ]
Rodriguez, G. [3 ]
机构：
[1] Univ Basque Country UPV EHU, CFAA, Parque Tecnol Zamudio 202, Bilbao 48170, Spain
[2] Univ Basque Country UPV EHU, Dept Mech Engn, Nieves Cano 12, Vitoria 01006, Spain
[3] Tecnalia Res & Innovat, Parque Cient & Tecnol Gipuzkoa, Donostia San Sebastian 20009, Spain
来源：
JOURNAL OF MANUFACTURING PROCESSES | 2021年 / 64卷
关键词：
CFRP; Ti6Al4V; Stacks drilling; Cryogenics CO2; MINIMUM QUANTITY LUBRICATION; TOOL WEAR; SURFACE INTEGRITY; CUTTING FLUID; CFRP; DESIGN; DAMAGE; DELAMINATION; WET;
D O I：
10.1016/j.jmapro.2021.01.018
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
In the work here presented, liquefied CO2 is used as cutting fluid for drilling CFRP-Ti6Al4V stacks as alternative to dry-drilling. Several tests were performed using dry-drilling technique, to compare this with the performance of CO2 cryogenic cooling. This work shows the feasibility of the proposed alternative, not only regarding technical issues but also environmental concerns. Results show that when CO2 is used in drilling, hole diameter values diverge below 0.5 % from nominal values, tool tip temperature is drastically reduced, and surface integrity of CFRP layers are preserved. Drilling tool edges damage is reduced and so tool life extended. In short, dry-drilling process was notably improved by CO2 assistance in comparison with dry drilling.
引用
收藏
页码：58 / 66
页数：9
相关论文
共 50 条
  • [1] Drilling of CFRP/Ti-6Al-4V Stacks
    Tashiro, Tetsuya
    Fujiwara, Junsuke
    Inada, Keiko
    ADVANCES IN ABRASIVE TECHNOLOGY XIV, 2011, 325 : 369 - +
  • [2] Investigation of minimum quantity lubrication effects in drilling CFRP/Ti6Al4V stacks
    Xu, Jinyang
    Ji, Min
    Chen, Ming
    Ren, Fei
    MATERIALS AND MANUFACTURING PROCESSES, 2019, 34 (12) : 1401 - 1410
  • [3] Effect of cooling strategies on performance and mechanism of helical milling of CFRP/Ti-6Al-4 V stacks
    Ge, Jiaying
    Chen, Guang
    Su, Yongxiang
    Zou, Yunhe
    Ren, Chengzu
    Qin, Xuda
    Wang, Guofeng
    CHINESE JOURNAL OF AERONAUTICS, 2022, 35 (02) : 388 - 403
  • [4] Drilling study on CFRP/Ti-6Al-4V stacks using chip breaker grooved drill
    Samsudeensadham, S.
    Krishnaraj, V
    MATERIALS AND MANUFACTURING PROCESSES, 2022, 37 (13) : 1511 - 1525
  • [5] Effects of Different Cooling Methods on the Specific Energy Consumption when Drilling CFRP/Ti6Al4V Stacks
    Ji, Min
    Xu, Jinyang
    Chen, Ming
    Mansori, Mohamed E. I.
    SUSTAINABLE MANUFACTURING - HAND IN HAND TO SUSTAINABILITY ON GLOBE, 2020, 43 : 95 - 102
  • [6] Drilling-induced damage suppression on CFRP/Ti-6Al-4V stacks using textured drills
    Samsudeensadham, S.
    Krishnaraj, V
    MATERIALS AND MANUFACTURING PROCESSES, 2024, 39 (11) : 1615 - 1629
  • [7] Experimental investigation on drilling machinability and hole quality of CFRP/Ti6Al4V stacks under different cooling conditions
    Xu, Jinyang
    Ji, Min
    Chen, Ming
    El Mansori, Mohamed
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2020, 109 (5-6) : 1527 - 1539
  • [8] A comparison between vibration assisted and conventional drilling of CFRP/Ti6Al4V stacks
    Xu, Jinyang
    Li, Chao
    Chen, Ming
    Ren, Fei
    MATERIALS AND MANUFACTURING PROCESSES, 2019, 34 (10) : 1182 - 1193
  • [9] An experimental study on abrasive waterjet cutting of CFRP/Ti6Al4V stacks for drilling operations
    Alberdi, A.
    Artaza, T.
    Suarez, A.
    Rivero, A.
    Girot, F.
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2016, 86 (1-4) : 691 - 704
  • [10] Orthogonal cutting mechanisms of CFRP/Ti6Al4V stacks
    Xu, Jinyang
    El Mansori, Mohamed
    Chen, Ming
    Ren, Fei
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2019, 103 (9-12) : 3831 - 3851
12345