Forced Cooling Friction Stir Welding of 2060-T8 Al-Li Alloy

被引：8

作者：

Niu, Shiyu ^{[1
]}

Yue, Yumei ^{[1
]}

Yan, Dejun ^{[2
]}

Ma, Zhongwei ^{[1
]}

Ji, Shude ^{[1
]}

机构：

[1] Shenyang Aerosp Univ, Fac Aerosp Engn, Shenyang 110136, Liaoning, Peoples R China

[2] CSSC Huangpu Wenchong Shipbldg Co Ltd, Guangdong Prov Key Lab Adv Welding Technol Ships, Guangzhou 510715, Guangdong, Peoples R China

来源：

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE | 2019年 / 28卷 / 09期

基金：

中国国家自然科学基金; 中国博士后科学基金;

关键词：

2060-T8 Al-Li alloy; forced cooling process; friction stir welding; mechanical properties; MECHANICAL-PROPERTIES; MATERIAL-FLOW; TENSILE PROPERTIES; MICROSTRUCTURE; EVOLUTION; GEOMETRY; BEHAVIOR; SPEED;

D O I：

10.1007/s11665-019-04255-0

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

Friction stir welding of 2060-T8 Al-Li alloy was experimentally investigated. Forced cooling process was realized by placing two copper pressure plates with a waterway on both sides of weld top surface. The relations between joint formation, microstructures and mechanical properties were mainly discussed. Compared with conventional joint by natural cooling, the welding joint with smaller flashes by forced cooling has the smaller well-distributed grains and higher microhardness in the stir zone (SZ). The tensile strength and elongation of forced cooling joint, respectively, reach 445.7 MPa and 6.7%, which are obviously higher than those of the conventional joint. The fracture locations of the conventional and forced cooling joints are located in the SZ, and the fracture surface morphologies show a typical ductile fracture mode.

引用

页码：5763 / 5771

页数：9

共 29 条

[1] Friction-stir welding of AA 2198 butt joints: mechanical characterization of the process and of the welds through DOE analysis
Bitondo, Ciro
Prisco, Umberto
Squilace, Antonino
Buonadonna, Pasquale
Dionoro, Gennaro
[J]. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2011, 53 (5-8) : 505 - 516
[2] Friction stir weld of 2060 Al-Cu-Li alloy: Microstructure and mechanical properties
Cai, B.
Zheng, Z. Q.
He, D. Q.
Li, S. C.
Li, H. P.
[J]. JOURNAL OF ALLOYS AND COMPOUNDS, 2015, 649 : 19 - 27
[3] Dan-dan Zhang, 2014, Advanced Materials Research, V1051, P799, DOI 10.4028/www.scientific.net/AMR.1051.799
[4] Characterization of high cycle fatigue behavior of a new generation aluminum lithium alloy
De, P. S.
Mishra, R. S.
Baumann, J. A.
[J]. ACTA MATERIALIA, 2011, 59 (15) : 5946 - 5960
[5] Material-flow behavior during friction-stir welding of 6082-T6 aluminum alloy
Huang, Yongxian
Wang, Yaobin
Wan, Long
Liu, Haoshu
Shen, Junjun
dos Santos, Jorge F.
Zhou, Li
Feng, Jicai
[J]. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2016, 87 (1-4) : 1115 - 1123
[6] In situ rolling friction stir welding for joining AA2219
Huang, Yongxian
Wan, Long
Lv, Shixiong
Zhang, Jian
Fu, Guansheng
[J]. MATERIALS & DESIGN, 2013, 50 : 810 - 816
[7] Effect of Temperature on Material Transfer Behavior at Different Stages of Friction Stir Welded 7075-T6 Aluminum Alloy
Ji, S. D.
Jin, Y. Y.
Yue, Y. M.
Gao, S. S.
Huang, Y. X.
Wang, L.
[J]. JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY, 2013, 29 (10) : 955 - 960
[8] Friction stir lap welding of Al to Mg assisted by ultrasound and a Zn interlayer
Ji, Shude
Niu, Shiyu
Liu, Jianguang
Meng, Xiangchen
[J]. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2019, 267 : 141 - 151
[9] Effect of Trailing Intensive Cooling on Residual Stress and Welding Distortion of Friction Stir Welded 2060 Al-Li Alloy
Ji, Shude
Yang, Zhanpeng
Wen, Quan
Yue, Yumei
Zhang, Liguo
[J]. HIGH TEMPERATURE MATERIALS AND PROCESSES, 2018, 37 (05) : 397 - 403
[10] Enhancing Friction Stir Weldability of 6061-T6 Al and AZ31B Mg Alloys Assisted by External Non-rotational Shoulder
Ji, Shude
Huang, Ruofei
Meng, Xiangchen
Zhang, Liguo
Huang, Yongxian
[J]. JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE, 2017, 26 (05) : 2359 - 2367

← 1 2 3 →