Modeling of dynamic recrystallization behavior of 21Cr-11Ni-N-RE lean austenitic heat-resistant steel during hot deformation

被引：40
作者：
Chen, Lei [1 ]
Zhang, Yingjie [2 ]
Li, Fei [2 ]
Liu, Xingang [2 ]
Guo, Baofeng [2 ]
Jin, Miao [2 ]
机构：
[1] Yanshan Univ, Natl Engn Res Ctr Equipment & Technol Cold Strip, Qinhuangdao 066004, Peoples R China
[2] Yanshan Univ, Sch Mech Engn, Qinhuangdao 066004, Peoples R China
来源：
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING | 2016年 / 663卷
基金：
中国国家自然科学基金;
关键词：
21Cr-11Ni-N-RE austenitic heat-resistant steel; Dynamic recrystallization; Kinetics model; Recrystallization region diagram; Grain size; NICKEL-BASED SUPERALLOY; INDUCED PLASTICITY STEEL; STAINLESS-STEEL; MICROSTRUCTURAL EVOLUTION; MICROALLOYED STEEL; MAGNESIUM ALLOY; TEMPERATURE; KINETICS; SURFACE;
D O I：
10.1016/j.msea.2016.03.119
中图分类号：
TB3 [工程材料学];
学科分类号：
0805 ; 080502 ;
摘要：
The dynamic recrystallization (DRX) behavior in 21Cr-11Ni-N-RE lean austenitic heat -resistant steel was investigated by hot compression tests within the temperature of 900-1200 degrees C and the strain rate of 0.0110 s(-1). The typical single-peak characteristic was observed in the most of resultant flow curves. On this basis, the related stress and strain peaks, recrystallization volume fraction were measured to quantify the kinetic models for DRX. A good agreement between the experimental and predicted results showed that the proposed kinetic equations can give an available estimate of the DRX evolution. In addition, the interpenetration of serrated grain boundary to viable recrystallized nuclei was considered to be a possible mechanism of initiation of DRX. Uniform and fine equiaxed grain structure could be obtained as a result of complete DRX, while abnormal grain growth may occur at high temperature and/or low strain rate after complete DRX. A DRX region diagram was developed to show the effect of deformation parameters on the DRX evolution; meanwhile a quantitative model was proposed to predict the final grain size in complete domain. (C) 2016 Elsevier B.V. All rights reserved.
引用
收藏
页码：141 / 150
页数：10
相关论文
共 44 条
[1]  
[Anonymous], E11212 ASTM INT
[2]   Predicting the critical strain for dynamic recrystallization using the kinetics of static recrystallization [J].
Barnett, MR ;
Kelly, GL ;
Hodgson, PD .
SCRIPTA MATERIALIA, 2000, 43 (04) :365-369
[3]   Processing Map and Hot Deformation Characteristics of 21Cr-11Ni-N-RE Lean Austenitic Heat-Resistant Steel [J].
Chen, Lei ;
Xue, Hongyan ;
Ma, Xiaocong ;
Jin, Miao ;
Long, Hongjun ;
Mao, Tianqiao ;
Wang, Jianfeng .
STEEL RESEARCH INTERNATIONAL, 2015, 86 (12) :1583-1593
[4]   Effect of rare earth element yttrium addition on microstructures and properties of a 21Cr-11Ni austenitic heat-resistant stainless steel [J].
Chen, Lei ;
Ma, Xiaocong ;
Wang, Longmei ;
Ye, Xiaoning .
MATERIALS & DESIGN, 2011, 32 (04) :2206-2212
[5]   The kinetics of dynamic recrystallization of 42CrMo steel [J].
Chen, Ming-Song ;
Lin, Y. C. ;
Ma, Xue-Song .
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2012, 556 :260-266
[6]   Microstructural evolution of a nickel-based superalloy during hot deformation [J].
Chen, Xiao-Min ;
Lin, Y. C. ;
Chen, Ming-Song ;
Li, Hong-Bin ;
Wen, Dong-Xu ;
Zhang, Jin-Long ;
He, Min .
MATERIALS & DESIGN, 2015, 77 :41-49
[7]   Dynamic recrystallization behavior of a typical nickel-based superalloy during hot deformation [J].
Chen, Xiao-Min ;
Lin, Y. C. ;
Wen, Dong-Xu ;
Zhang, Jin-Long ;
He, Min .
MATERIALS & DESIGN, 2014, 57 :568-577
[8]   Recrystallization in AISI 304 austenitic stainless steel during and after hot deformation [J].
Dehghan-Manshadi, A. ;
Barnett, M. R. ;
Hodgson, P. D. .
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2008, 485 (1-2) :664-672
[9]   A new method for evaluation of friction in bulk metal forming [J].
Ebrahimi, R ;
Najafizadeh, A .
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2004, 152 (02) :136-143
[10]   Dynamic recrystallization of austenite in microalloyed high carbon steels [J].
Elwazri, AM ;
Wanjara, P ;
Yue, S .
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2003, 339 (1-2) :209-215
12345