Evolutions of cylinder liner surface texture and tribological performance of piston ring-liner assembly

被引：55

作者：

Grabon, Wieslaw ^{[1
]}

Pawlus, Pawel ^{[1
]}

Wos, Slawomir ^{[1
]}

Koszela, Waldemar ^{[1
]}

Wieczorowski, Michal ^{[2
]}

机构：

[1] Rzeszow Univ Technol, Fac Mech Engn & Aeronaut, Powstancow Warszawy 12, PL-35959 Rzeszow, Poland

[2] Poznan Univ Tech, Piotrowo 2, PL-61138 Poznan, Poland

来源：

TRIBOLOGY INTERNATIONAL | 2018年 / 127卷

关键词：

Cylinder liner; Two-process surfaces; Coefficient of friction; MUTUAL INFLUENCE; HONED SURFACE; ROUGHNESS; FRICTION; PARAMETERS; WEAR; ANGLE;

D O I：

10.1016/j.triboint.2018.07.011

中图分类号：

TH [机械、仪表工业];

学科分类号：

0802 ;

摘要：

This paper presents the results of the tribological experiments conducted using an oscillating wear tester under lubricated conditions. Specimen from piston ring slid against counter-specimen from cylinder liner. Various surface textures of cylinder liners resulted from honing and/or plateau honing. Tests were carried out for two normal loads of 100 and 300 N at a temperature of 80 degrees C, the stroke was 3 mm, the frequency was 10 Hz. Each experiment was divided into four time intervals. During breaks between the particular parts of the test, the surface topography of cylinder liners was measured by a white light interferometer. It was found that an increase in the normal load led to an increase in changes of the liner surface textures.

引用

页码：545 / 556

页数：12

共 39 条

[1] Liner surface improvements for low friction piston ring packs [J].

Anderberg, C. ;

Dimkovski, Z. ;

Rosen, B-G .

SURFACE TOPOGRAPHY-METROLOGY AND PROPERTIES, 2014, 2 (01)

[2]

[Anonymous], 2004, P 2004 FALL TECHN C

[3]

[Anonymous], 1993, CIRP ANN-MANUF TECHN, DOI DOI 10.1016/S0007-8506(07)62527-X

[4] Determination of fundamental parameters for the cross-hatched cylinder liner micro-geometry [J].

Biboulet, N. ;

Bouassida, H. ;

Cavoret, J. ;

Lubrecht, A. A. .

PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART J-JOURNAL OF ENGINEERING TRIBOLOGY, 2017, 231 (03) :293-301

[5] Piston ring load carrying capacity: Influence of cross-hatching parameters [J].

Bouassida, H. ;

Biboulet, N. ;

Sainsot, P. ;

Lubrecht, A. A. .

PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART J-JOURNAL OF ENGINEERING TRIBOLOGY, 2014, 228 (06) :642-648

[6] Use of roughness probability parameters to quantify the material removed in plateau-honing [J].

Buj Corral, Irene ;

Vivancos Calvet, Joan ;

Coba Salcedo, Milton .

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE, 2010, 50 (07) :621-629

[7] CYLINDER BORE SURFACE-ROUGHNESS IN INTERNAL COMBUSTION ENGINES - ITS APPRECIATION AND CONTROL [J].

CAMPBELL, JC .

WEAR, 1972, 19 (02) :163-&

[8]

Golloch R., 2004, PROCEDDINGS 14 INT C, P321

[9] Effects of cylinder liner surface topography on friction and wear of liner-ring system at low temperature [J].

Grabon, Wieslaw ;

Pawlus, Pawel ;

Wos, Slawomir ;

Koszela, Waldemar ;

Wieczorowski, Michal .

TRIBOLOGY INTERNATIONAL, 2018, 121 :148-160

[10] Effects of honed cylinder liner surface texture on tribological properties of piston ring-liner assembly in short time tests [J].

Grabon, Wieslaw ;

Pawlus, Pawel ;

Wos, Slawomir ;

Koszela, Waldemar ;

Wieczorowski, Michal .

TRIBOLOGY INTERNATIONAL, 2017, 113 :137-148

← 1 2 3 4 →