Study of the tribological synergistic effects in nano CuO-filled and fiber-reinforced polyphenylene sulfide composites

被引:103
作者
Cho, MH [1 ]
Bahadur, S [1 ]
机构
[1] Iowa State Univ Sci & Technol, Dept Mech Engn, Ames, IA 50011 USA
关键词
wear; friction; PPS; filler; fiber reinforcement; hybrid composites; transfer film analysis; wear inechanisins; topographic analysis;
D O I
10.1016/j.wear.2004.09.055
中图分类号
TH [机械、仪表工业];
学科分类号
0802 ;
摘要
Nanosize CuO-filled and fiber-reinforced polyphenylene sulfide (PPS) composites were prepared by compression molding. The tribological behaviors of these materials and the synergism as a result of the incorporation of both the nanoparticles and the fibers were investigated. The reinforcement materials were short carbon fibers (CF) and aramid (Kevlar) fibers. The proportions of the filler material varied from 1 to 4 vol.% and of the reinforcement material from 5 to 15 vol.%. For the measurement of wear volume and the coefficient of friction, a pin-on-disk sliding configuration was used. The counterface was made of tool steel hardened to 55-60HRC and finished to 0.09-0.11 mum Ra. Wear tests were run at a sliding speed of 1 m/s and over a duration of 6 h, which provided the wear data for steady state sliding. In case of the filler only, the lowest steady state wear rate was observed for PPS + 2 %CuO composite and of the fiber reinforcement only for PPS + 10 % Kevlar composite. The particulate filler did not affect much the coefficient of friction while the latter was reduced to half of that in the case of CF reinforcement. The lowest steady state wear rates that were obtained with hybrid composites made with nanosize CuO particles and fiber reinforcement both could not be obtained with the composites made with either the filler or the fiber reinforcement only. With Kevlar fiber reinforcement alone. the coefficient of friction did not change much. With reinforcement of the CuO-filled polymer with Kevlar fibers, the coefficient of friction increased. but with reinforcement with carbon fibers it either decreased or remained unaffected. The transfer films were studied by optical microscopy and the topographical changes of transfer films by atomic force microscopy (AFM). Worn surfaces and transfer films on the counterface were also studied by scanning electron microscopy. (C) 2004 Elsevier B.V. All rights reserved.
引用
收藏
页码:835 / 845
页数:11
相关论文
共 50 条
[41]   Study on the Tribological Properties of Carbon Fabric Reinforced Phenolic Composites Filled with Nano-Al2O3 [J].
Zhang, Xinrui .
JOURNAL OF MACROMOLECULAR SCIENCE PART B-PHYSICS, 2017, 56 (08) :568-577
[42]   Tribological Properties of Cyperus pangorei Fiber-Reinforced Polyester Composites (Friction and Wear Behavior of Cyperus pangorei Fiber/Polyester Composites) [J].
Rajini, N. ;
Mayandi, K. ;
Prabhakar, Manoj M. ;
Siengchin, Suchart ;
Ayrilmis, Nadir ;
Bennet, C. ;
Ismail, S. O. .
JOURNAL OF NATURAL FIBERS, 2021, 18 (02) :261-273
[43]   Mechanical Properties and Vibrational Behavior of 3D-Printed Carbon Fiber-Reinforced Polyphenylene Sulfide and Polyamide-6 Composites with Different Infill Types [J].
Papageorgiou, Vasileios ;
Tsongas, Konstantinos ;
Mansour, Michel Theodor ;
Tzetzis, Dimitrios ;
Mansour, Gabriel .
JOURNAL OF COMPOSITES SCIENCE, 2025, 9 (02)
[44]   Mechanical and Tribological Properties of Solid Lubricant (PTFE) Filled Carbon Fiber Reinforced Polycarbonate Composites [J].
Shamsuddin, M. S. M. ;
Nasir, R. M. ;
Hassan, Aziz ;
Ishak, Z. A. Mohd .
3RD INTERNATIONAL POSTGRADUATE CONFERENCE ON MATERIALS, MINERALS & POLYMER (MAMIP) 2019, 2020, 2267
[45]   Studies on Tribological Behavior of Polyamide Filled Jute Fiber-Nano-ZnO Hybrid Composites [J].
Rajasekhar, P. ;
Ganesan, G. ;
Senthilkumar, C. .
12TH GLOBAL CONGRESS ON MANUFACTURING AND MANAGEMENT (GCMM - 2014), 2014, 97 :2099-2109
[46]   Study on the Friction and Sliding Wear Behavior of Hybrid Polytetrafluoroethylene/Kevlar Fabric Composites Filled with Polyphenylene Sulfide [J].
Huang, Ting ;
Lu, Renguo ;
Ma, Yuning ;
Liu, Pei ;
Li, Tongsheng .
JOURNAL OF MACROMOLECULAR SCIENCE PART B-PHYSICS, 2012, 51 (1-3) :109-124
[47]   A New Way of Strengthening and Toughening for Carbon Fiber Reinforced Polyphenylene Sulfide (CF/PPS) Composites via Matrix Modification [J].
Xu Yingkai ;
Zhu Shu ;
Zhang Zhao ;
Yu Muhuo ;
Yuan Xiangkai .
JOURNAL OF WUHAN UNIVERSITY OF TECHNOLOGY-MATERIALS SCIENCE EDITION, 2017, 32 (06) :1318-1322
[48]   MECHANICAL AND TRIBOLOGICAL PROPERTIES OF EPOXY-BASED NATURAL FIBER-REINFORCED HYBRID BIO-COMPOSITES [J].
Singh, Lokesh kumar ;
Yadav, Prabhat chand ;
Katiyar, Prvan kumar ;
Maurya, Rita .
SURFACE REVIEW AND LETTERS, 2025,
[49]   Kenaf/glass fiber-reinforced polymer composites: Pioneering sustainable materials with enhanced mechanical and tribological properties [J].
Supian, A. B. M. ;
Asyraf, M. R. M. ;
Syamsir, Agusril ;
Ma, Quanjin ;
Hazrati, K. Z. ;
Azlin, M. N. M. ;
Mubarak Ali, M. ;
Ghani, Aizat ;
Hua, Lee Seng ;
Saifulazry, Syeed ;
Razman, M. R. ;
Ramli, Zuliskandar ;
Nurazzi, N. M. ;
Norrrahim, M. N. F. ;
Thiagamani, Senthil Muthu Kumar .
POLYMER COMPOSITES, 2024, 45 (16) :14421-14447
[50]   Tribological Behavior of Surface Textured Short Carbon Fiber-Reinforced Nylon Composites Fabricated by Three-Dimensional Printing Techniques [J].
Luo, Ming ;
He, Qinghao ;
Wang, Hongjian ;
Chang, Li .
JOURNAL OF TRIBOLOGY-TRANSACTIONS OF THE ASME, 2021, 143 (05)