Deep drawing simulation of a metastable austenitic stainless steel using a two-phase model

被引：20

作者：

Gallee, S. ^{[1
]}

Pilvin, P. ^{[1
]}

机构：

[1] Univ Bretagne Sud, Lab Ingn MAT Bretagne, F-56321 Lorient, France

来源：

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY | 2010年 / 210卷 / 6-7期

关键词：

Stainless steel; Martensitic transformation; Two-phase model; Numerical simulation; Deep drawing; Eddy Current measurements; INDUCED MARTENSITIC-TRANSFORMATION; DEFORMATION-INDUCED TRANSFORMATION; FINITE-ELEMENT-ANALYSIS; TRIP STEEL; CONSTITUTIVE MODEL; NUMERICAL-ANALYSIS; STRAIN STATE; SHEET; BEHAVIOR; FORMABILITY;

D O I：

10.1016/j.jmatprotec.2010.01.008

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

This paper deals with the numerical simulation of the deep drawing of a metastable austenitic stainless steel of AISI 304 type. A two-phase model of elastoviscoplastic type has been developed by Gallee et al. (2007) to take into account the martensitic transformation induced by plastic deformation during cold forming that can exhibit this stainless steel. This two-phase model is used to describe the behavior of the steel during the numerical simulation of the deep drawing of a cylinder cup using a commercial finite element code. The numerical results of the simulations are compared with experimental results of the same deep drawing test in order to validate the model. (C) 2010 Elsevier B.V. All rights reserved.

引用

页码：835 / 843

页数：9

共 37 条

[1]

Amstrong P.J., 1966, GEGB REPORT RDBN, P731

[2] Delayed cracking in 301LN austenitic steel after deep drawing: Martensitic transformation and residual stress analysis [J].

Berrahmoune, M. R. ;

Berveiller, S. ;

Inal, K. ;

Patoor, E. .

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2006, 438 :262-266

[3] EXTENSION OF THE SELF-CONSISTENT SCHEME TO PLASTICALLY-FLOWING POLYCRYSTALS [J].

BERVEILLER, M ;

ZAOUI, A .

JOURNAL OF THE MECHANICS AND PHYSICS OF SOLIDS, 1978, 26 (05) :325-344

[4] Strain induced martensite formation and its effect on strain hardening behavior in the cold drawn 304 austenitic stainless steels [J].

Choi, JY ;

Jin, W .

SCRIPTA MATERIALIA, 1997, 36 (01) :99-104

[5] A model for strain-induced martensitic transformation of TRIP steel with strain rate [J].

Dan, W. J. ;

Zhang, W. G. ;

Li, S. H. ;

Lin, Z. Q. .

COMPUTATIONAL MATERIALS SCIENCE, 2007, 40 (01) :101-107

[6] Finite element simulation on strain-induced martensitic transformation effects in TRIP steel sheet forming [J].

Dan, W. J. ;

Zhang, W. G. ;

Li, S. H. ;

Lin, Z. Q. .

COMPUTATIONAL MATERIALS SCIENCE, 2007, 39 (03) :593-599

[7] Mechanical behavior of a metastable austenitic stainless steel under simple and complex loading paths [J].

Gallee, S. ;

Manach, P. Y. ;

Thuillier, S. .

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2007, 466 (1-2) :47-55

[8]

GALLEE S, 2003, MATERIAUX TECHNIQUES, V3, P1

[9] A constitutive model for the formation of martensite in austenitic steels under large strain plasticity [J].

Hallberg, Hakan ;

Hakansson, Paul ;

Ristinmaa, Matti .

INTERNATIONAL JOURNAL OF PLASTICITY, 2007, 23 (07) :1213-1239

[10] EFFECTS OF STRAIN STATE AND STRAIN RATE ON DEFORMATION-INDUCED TRANSFORMATION IN 304 STAINLESS-STEEL .1. MAGNETIC MEASUREMENTS AND MECHANICAL-BEHAVIOR [J].

HECKER, SS ;

STOUT, MG ;

STAUDHAMMER, KP ;

SMITH, JL .

METALLURGICAL TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE, 1982, 13 (04) :619-626

← 1 2 3 4 →