Effect of Cr Content on the Compression Properties and Abrasive Wear Behavior of the High-Volume Fraction (TiC-TiB2)/Cu Composites

被引：17

作者：

Qiu, Feng ^{[1
]}

Han, Yue ^{[1
]}

Cheng, Ai ^{[1
]}

Lu, Jianbang ^{[1
]}

Jiang, Qichuan ^{[1
]}

机构：

[1] Jilin Univ, Key Lab Automobile Mat, Minist Educ, Dept Mat Sci & Engn, Changchun 130025, Peoples R China

来源：

ACTA METALLURGICA SINICA-ENGLISH LETTERS | 2014年 / 27卷 / 05期

基金：

中国国家自然科学基金; 高等学校博士学科点专项科研基金;

关键词：

Metal matrix composites; Powder metallurgy; Combustion synthesis; Abrasive wear; COPPER MATRIX COMPOSITES; IN-SITU SYNTHESIS; MECHANICAL-PROPERTIES; CARBON; MICROSTRUCTURE; TIB2;

D O I：

10.1007/s40195-014-0158-8

中图分类号：

TF [冶金工业];

学科分类号：

0806 ;

摘要：

The (TiC-TiB2)/Cu composites with 50 vol% TiC-TiB2 ceramic particles were successfully fabricated by the combustion synthesis and hot press consolidation in a Cu-Ti-B4C-Cr system. The effects of the Cr content on the microstructures, hardness, compression properties, and abrasive wear behaviors of the composites were investigated. The final products consist of only Cu, TiC, and TiB2 phases, and the ceramic particles are distributed uniformly in these composites. The size of the ceramic particles decreases with Cr addition. As the Cr content increases, the yield strength, ultimate compression strength, microhardness, and abrasive wear resistance of the composites increase, and the fracture strain decreases.

引用

页码：951 / 956

页数：6

共 50 条

[1] Effect of Cr Content on the Compression Properties and Abrasive Wear Behavior of the High-Volume Fraction(TiC–TiB2)/Cu Composites
Feng Qiu
Yue Han
Ai Cheng
Jianbang Lu
Qichuan Jiang
Acta Metallurgica Sinica(English Letters), 2014, 27 (05) : 951 - 956
[2] Effect of Cr Content on the Compression Properties and Abrasive Wear Behavior of the High-Volume Fraction (TiC–TiB2)/Cu Composites
Feng Qiu
Yue Han
Ai Cheng
Jianbang Lu
Qichuan Jiang
Acta Metallurgica Sinica (English Letters), 2014, 27 : 951 - 956
[3] Compression properties and abrasive wear behavior of high volume fraction TiCx-TiB2/Cu composites fabricated by combustion synthesis and hot press consolidation
Lu, Jianbang
Shu, Shili
Qiu, Feng
Wang, Yawei
Jiang, Qichuan
MATERIALS & DESIGN, 2012, 40 : 157 - 162
[4] Effect of W content on the compression properties and abrasive wear behavior of the (TiB2-TiCxNy)/(Ni plus W) composites
Wang, Yawei
Shu, Shili
Qiu, Feng
Zhou, Dongshuai
Wang, Jinguo
Jiang, Qichuan
MATERIALS & DESIGN, 2013, 45 : 286 - 291
[5] Effect of Ni content on the compression properties and abrasive wear behavior of the (TiB2-TiCxNy)/Ni composites
Wang, Yawei
Qiu, Feng
Shu, Shili
Lu, Jianbang
Jiang, Qichuan
INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS, 2012, 34 : 8 - 12
[6] Preparation and Characterization of In Situ (TiC-TiB2)/Al-Cu-Mg-Si Composites with High Strength and Wear Resistance
Gao, Yu-Yang
Liu, Ying
Li, Yuan-Lin
Zhang, Ang
Teng, Hang
Dong, Zhi-Hua
Li, Tian
Jiang, Bin
MATERIALS, 2022, 15 (24)
[7] Microstructure, mechanical properties, electrical conductivity and wear behavior of high volume TiC reinforced Cu-matrix composites
Akhtar, Farid
Askari, Syed Javid
Shah, Khadijah Ali
Du, Xueli
Guo, Shiju
MATERIALS CHARACTERIZATION, 2009, 60 (04) : 327 - 336
[8] Dry Sliding Wear Properties of Annealed Carbon Steels Matrix Composites by Nanosized TiC-TiB2 Particles
Zhang, Yu
Wang, Bingxu
Qiu, Feng
Dong, Baixin
Wu, Zhijun
Li, Hongjun
Barber, Gary C. C.
ADVANCED ENGINEERING MATERIALS, 2023, 25 (20)
[9] Effects of Cr and Zr Addition on Microstructures, Compressive Properties, and Abrasive Wear Behaviors of In Situ TiB2/Cu Cermets
Qiu, Feng
Duan, Xiangzheng
Dong, Baixin
Yang, Hongyu
Lu, Jianbang
Li, Xiujuan
MATERIALS, 2018, 11 (08)
[10] Microstructures and properties of large bulk solidified TiC-TiB2 composites prepared by combustion synthesis under high gravity
Zhao, Zhongmin
Zhang, Long
Song, Yigang
Wang, Weiguo
Liu, Hongbo
SCRIPTA MATERIALIA, 2009, 61 (03) : 281 - 284

← 1 2 3 4 5 →