Influence of resin curing cycle on the deformation of filament wound composites by in situ strain monitoring

被引:15
作者
Chen, Xiaodong [1 ]
Li, Yong [2 ]
Huan, Dajun [1 ]
Wang, Wuqiang [1 ]
Jiao, Yang [1 ]
机构
[1] Nanjing Univ Aeronaut & Astronaut, Coll Mat Sci & Technol, Nanjing, Peoples R China
[2] Nanjing Univ Aeronaut & Astronaut, Natl Key Lab Sci & Technol Helicopter Transmiss, Nanjing, Peoples R China
关键词
Epoxy resin; cure behavior; process monitoring; filament wound composite; ENABLED FIBER SENSORS; DESIGN OPTIMIZATION; RESIDUAL-STRESS; MANDREL; FABRICATION; SIMULATION; STRATEGY; BEHAVIOR; SYSTEM;
D O I
10.1177/09540083211026359
中图分类号
O63 [高分子化学(高聚物)];
学科分类号
070305 ; 080501 ; 081704 ;
摘要
The residual stress of metal liners wrapped by composite materials has a significant influence on the service performance of rotating parts, such as flywheel rotors and motor jackets. However, the deformation of the liners, the flow of resins, and the temperature variation during the winding process make it difficult to predict and control this residual stress. In this paper, the process-induced strains were monitored online by a strain gauge with the help of a wireless strain meter. The evolution of this strain during the manufacturing process was fully discussed. A rapid curing resin system was used and its curing properties were tested by differential scanning calorimetry. The mechanical properties of the resin matrix and its composite were characterized. The effect of the curing cycle on the evolution of the residual strain was discussed in detail through comparative experiments. The experimental results show that the use of infrared radiation has a significant advantage regarding residual stress accumulation. This advantage is greater when carbon fiber is used than when glass fiber is used. The prestress in composites of glass fiber and carbon fiber increases by 5.9% and 41.7%, respectively, after cooling.
引用
收藏
页码:1141 / 1152
页数:12
相关论文
共 42 条
[1]   Slitting Measurement of Residual Hoop Stresses Through the Wall-Thickness of a Filament Wound Composite Ring [J].
Akbari, S. ;
Taheri-Behrooz, F. ;
Shokrieh, M. M. .
EXPERIMENTAL MECHANICS, 2013, 53 (09) :1509-1518
[2]   Graphene coated piezo-resistive fabrics for liquid composite molding process monitoring [J].
Ali, Muhammad A. ;
Umer, Rehan ;
Khan, Kamran A. ;
Samad, Yarjan A. ;
Liao, Kin ;
Cantwell, Wesley .
COMPOSITES SCIENCE AND TECHNOLOGY, 2017, 148 :106-114
[3]   Optimal design of press-fitted filament wound composite flywheel rotors [J].
Arvin, AC ;
Bakis, CE .
COMPOSITE STRUCTURES, 2006, 72 (01) :47-57
[4]   Design and Experimental Evaluation of a Low-Cost Test Rig for Flywheel Energy Storage Burst Containment Investigation [J].
Buchroithner, Armin ;
Haidl, Peter ;
Birgel, Christof ;
Zarl, Thomas ;
Wegleiter, Hannes .
APPLIED SCIENCES-BASEL, 2018, 8 (12)
[5]   FILAMENT WINDING CYLINDERS .2. VALIDATION OF THE PROCESS MODEL [J].
CALIUS, EP ;
LEE, SY ;
SPRINGER, GS .
JOURNAL OF COMPOSITE MATERIALS, 1990, 24 (12) :1299-1343
[6]  
Castani? B, 2021, COMPOS PART A-APPL S, V142, P106
[7]   Experimental Characterization of CFRP by NOL Ring Test [J].
Charan, V. SaiSri ;
Vardhan, A. Vishnu ;
Raj, Sai ;
Rao, G. Rama ;
Rao, G. V. ;
Hussaini, S. M. .
MATERIALS TODAY-PROCEEDINGS, 2019, 18 :2868-2874
[8]   Studies on thermal, mechanical, electrical, and morphological behavior of organoclay-reinforced polybenzoxazine-epoxy nanocomposites [J].
Chozhan, C. Karikal ;
Chandramohan, Ayyavu ;
Alagar, Muthukaruppan .
HIGH PERFORMANCE POLYMERS, 2013, 25 (08) :1007-1021
[9]  
Conteh Michael A., 2016, J. appl. res. technol, V14, P184, DOI 10.1016/j.jart.2016.04.005
[10]   Structural health monitoring with piezoelectric wafer active sensors for space applications [J].
Cuc, Adrian ;
Giurgiutiu, Victor ;
Joshi, Shiv ;
Tidwell, Zeb .
AIAA JOURNAL, 2007, 45 (12) :2838-2850