Influence of friction on the loads in a roll forming simulation with compliant rolls

被引:6
作者
Mueller, Christian [1 ]
Gu, Xun [1 ]
Baeumer, Lars [1 ]
Groche, Peter [1 ]
机构
[1] Tech Univ Darmstadt, Inst Prod Engn & Forming Machines, D-64287 Darmstadt, Germany
来源
MATERIAL FORMING ESAFORM 2014 | 2014年 / 611-612卷
关键词
roll forming; simulation; friction; torque;
D O I
10.4028/www.scientific.net/KEM.611-612.436
中图分类号
T [工业技术];
学科分类号
08 ;
摘要
Roll forming is an important economic forming process for manufacturing of profiles. For an optimal design of the process, it is important to determine the loads occurring during the forming process. Furthermore, the information of the load behavior enables an evaluation of the formability of the planned profiles with the chosen roll forming machine. An experimental determination of loads in roll forming processes requires a complex measurement setup in combination with a high amount of measurement devices. Hence, the analysis of roll loads by means of finite element simulation is of special interest. The use of roll forming simulations for the determination of geometrical outputs is state of the art. However, due to simplifications, a realistic and reliable output of roll loads in roll forming is impossible. Therefore, the compliance behavior under load and the frictional behavior have to be incorporated in the simulation model. The friction behavior in roll forming processes is presented to be very insignificant in literature. The value of the friction coefficients vary in a broad range. Due to lack of knowledge in the compliance behavior of the used stands, simulation models with rigid rolls are still state of the art. This paper will show the reproduction of realistic roll loads, e. g. torques and forces, in a roll forming simulation. Therefore, the friction coefficients of each roll-sheet metal contact will be gained experimentally and implemented in the numerical model. Furthermore, a characteristic compliance of the roll forming stands will be analyzed and also considered in the simulation. Finally, the influence of changing parameters, e.g. raise of the friction coefficients, on the roll loads will be investigated. To verify the simulation the numerical results will be compared to data gained by experiments.
引用
收藏
页码:436 / 443
页数:8
相关论文
共 50 条
[31]   Process parameters influence on friction coefficient in sheet forming operations [J].
E. Ceretti ;
A. Fiorentino ;
C. Giardini .
International Journal of Material Forming, 2008, 1 :1219-1222
[32]   Process parameters influence on friction coefficient in sheet forming operations [J].
Ceretti, E. ;
Fiorentino, A. ;
Giardini, C. .
INTERNATIONAL JOURNAL OF MATERIAL FORMING, 2008, 1 (Suppl 1) :1219-1222
[33]   Research on Influence Factors of Cold Roll-beating Forming Forces of Leadscrews [J].
Li Y. ;
Li Y. ;
Cui L. ;
Miao Z. .
Zhongguo Jixie Gongcheng/China Mechanical Engineering, 2020, 31 (09) :1065-1073
[34]   Numerical simulation and parameters analysis for roll forming of martensitic steel MS980 [J].
Kang, Wen ;
Zhao, Yixi ;
Yu, Wangwei ;
Wang, Shanshuai ;
Ma, Yuefeng ;
Yan, Peijie .
11TH INTERNATIONAL CONFERENCE ON TECHNOLOGY OF PLASTICITY, ICTP 2014, 2014, 81 :251-256
[35]   FEM dynamic simulation and analysis of the roll-bending process for forming a conical tube [J].
Zeng, Jun ;
Liu, Zhaohenq ;
Champliaud, Henri .
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2008, 198 (1-3) :330-343
[36]   Numerical Simulation of the Roll Forming Process of Aluminum Folded Micro-channel Tube [J].
Zou, Tianxia ;
Zhou, Ning ;
Peng, Yinghong ;
Tang, Ding ;
Li, Dayong .
NUMISHEET 2016: 10TH INTERNATIONAL CONFERENCE AND WORKSHOP ON NUMERICAL SIMULATION OF 3D SHEET METAL FORMING PROCESSES, PTS A AND B, 2016, 734
[37]   Simulation of cold roll forming using elastic-plastic finite element method [J].
Chen, Xia ;
Chang, Qingming ;
Wang, Jiao ;
Chen, Changjun .
International Journal of Modelling, Identification and Control, 2009, 7 (01) :97-102
[38]   3D strip model for continuous roll-forming process simulation [J].
Esposito, Luca ;
Bertocco, Alcide ;
Sepe, Raffaele ;
Armentani, Enrico .
AIAS 2018 INTERNATIONAL CONFERENCE ON STRESS ANALYSIS, 2018, 12 :370-379
[39]   Numerical simulation of roll-forming by B-spline finite strip method [J].
Liu, C ;
Zhou, Y ;
Lu, W .
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 1996, 60 (1-4) :215-218
[40]   Influence of Die Machining Operation on the Friction Condition in the Cold Forming Process [J].
Hosseinpour, Gholamreza ;
Gerdooei, Mahdi ;
Alimirzaloo, Vali .
TRIBOLOGY TRANSACTIONS, 2021, 64 (02) :193-201