Parameter calibration of discrete element method modelling for cohesive and non-spherical particles of powder

被引：56

作者：

Hoshishima, Chiho ^{[1
]}

Ohsaki, Shuji ^{[1
]}

Nakamura, Hideya ^{[1
]}

Watano, Satoru ^{[1
]}

机构：

[1] Osaka Prefecture Univ, Dept Chem Engn, Naka Ku, 1-1 Gakuen Cho, Sakai, Osaka 5998531, Japan

来源：

POWDER TECHNOLOGY | 2021年 / 386卷

关键词：

DEM modelling; Parameter calibration; Coefficient of rolling friction; Surface energy; DEM PARAMETERS; GRANULAR MATERIAL; SCALE-UP; SIMULATION; FLOW; REPOSE; ANGLE; COHESIONLESS; FRAMEWORK; DYNAMICS;

D O I：

10.1016/j.powtec.2021.03.044

中图分类号：

TQ [化学工业];

学科分类号：

0817 ;

摘要：

Numerical analysis via the DEM has been applied to various powder processes. To obtain simulation results of high reliability, a calibration method for the input DEM parameters must be established. This paper therefore proposes a calibration procedure for non-spherical cohesive particles. The rolling friction coefficient and surface energy for cohesive force based on the JKR theory were calibrated. Initially, the dynamic angles of repose were calculated using various parameter combinations to obtain a two-dimensional contour map. Subsequently, the DEM parameters were determined by comparing them with the experimental data. Finally, the theoretical static angle of repose was calculated using the selected parameters to verify its agreement with the experimental data, which confirmed its validity. Furthermore, the validity of the calibrated parameters was evaluated by mixing simulations in a V-shaped mixer. Through the proposed calibration procedure, the DEM parameters of several materials were obtained successfully, and their wide applicability was confirmed. (c) 2021 Elsevier B.V. All rights reserved.

引用

页码：199 / 208

页数：10

共 33 条

[21] DEM simulation on the vibrated packing densification of mono-sized equilateral cylindrical particles [J].

Qian, Quan ;

Wang, Lin ;

An, Xizhong ;

Wu, Yongli ;

Wang, Ju ;

Zhao, Haiyang ;

Yang, Xiaohong .

POWDER TECHNOLOGY, 2018, 325 :151-160

[22] A methodical calibration procedure for discrete element models [J].

Rackl, Michael ;

Hanley, Kevin J. .

POWDER TECHNOLOGY, 2017, 307 :73-83

[23] Development of a standard calibration procedure for the DEM parameters of cohesionless bulk materials - Part II: Efficient optimization-based calibration [J].

Richter, Christian ;

Roessler, Thomas ;

Kunze, Guenter ;

Katterfeld, Andre ;

Will, Frank .

POWDER TECHNOLOGY, 2020, 360 :967-976

[24] Development of a standard calibration procedure for the DEM parameters of cohesionless bulk materials - part I: Solving the problem of ambiguous parameter combinations [J].

Roessler, Thomas ;

Richter, Christian ;

Katterfeld, Andre ;

Will, Frank .

POWDER TECHNOLOGY, 2019, 343 :803-812

[25] Scaling of the angle of repose test and its influence on the calibration of DEM parameters using upscaled particles [J].

Roessler, Thomas ;

Katterfeld, Andre .

POWDER TECHNOLOGY, 2018, 330 :58-66

[26] A comprehensive review on process and engineering aspects of pharmaceutical wet granulation [J].

Suresh, P. ;

Sreedhar, I. ;

Vaidhiswaran, R. ;

Venugopal, A. .

CHEMICAL ENGINEERING JOURNAL, 2017, 328 :785-815

[27] Scaling of discrete element model parameters for cohesionless and cohesive solid [J].

Thakur, Subhash C. ;

Ooi, Jin Y. ;

Ahmadian, Hossein .

POWDER TECHNOLOGY, 2016, 293 :130-137

[28] DEM-based modelling framework for spray-dried powders in ceramic tiles industry. Part I: Calibration procedure [J].

Tiscar, J. M. ;

Escrig, A. ;

Mallol, G. ;

Boix, J. ;

Gilabert, F. A. .

POWDER TECHNOLOGY, 2019, 356 :818-831

[29]

Watanabe R., 2019, J SOC POWDER TECHNOL, V56, P218

[30] Numerical simulation of particle dynamics in different flow regimes in a rotating drum [J].

Yang, R. Y. ;

Yu, A. B. ;

McElroy, L. ;

Bao, J. .

POWDER TECHNOLOGY, 2008, 188 (02) :170-177

← 1 2 3 4 →