Rock Fracture Toughness Study Under Mixed Mode I/III Loading

被引:125
作者
Aliha, M. R. M. [1 ]
Bahmani, A. [1 ,2 ]
机构
[1] IUST, Sch Ind Engn, Welding & Joining Res Ctr, Tehran 1684613114, Iran
[2] Univ Waterloo, Dept Mech & Mechatron Engn, 200 Univ Ave West, Waterloo, ON N2L 3G1, Canada
关键词
Mixed mode I/III; Marble rock; Novel disc shape specimen; K-Ic-K-IIIc data; Fracture models; BRAZILIAN DISC SPECIMEN; II FRACTURE; BRITTLE-FRACTURE; LIMESTONE ROCK; STRAIN-ENERGY; V-NOTCHES; BEHAVIOR; STRESS; GEOMETRY; MARBLE;
D O I
10.1007/s00603-017-1201-7
中图分类号
P5 [地质学];
学科分类号
0709 ; 081803 ;
摘要
Fracture growth in underground rock structures occurs under complex stress states, which typically include the in- and out-of-plane sliding deformation of jointed rock masses before catastrophic failure. However, the lack of a comprehensive theoretical and experimental fracture toughness study for rocks under contributions of out-of plane deformations (i.e. mode III) is one of the shortcomings of this field. Therefore, in this research the mixed mode I/III fracture toughness of a typical rock material is investigated experimentally by means of a novel cracked disc specimen subjected to bend loading. It was shown that the specimen can provide full combinations of modes I and III and consequently a complete set of mixed mode I/III fracture toughness data were determined for the tested marble rock. By moving from pure mode I towards pure mode III, fracture load was increased; however, the corresponding fracture toughness value became smaller. The obtained experimental fracture toughness results were finally predicted using theoretical and empirical fracture models.
引用
收藏
页码:1739 / 1751
页数:13
相关论文
共 66 条
[1]  
Abd-Elhady A., 2013, Eng. Solid Mech., V1, P119, DOI 10.5267/j.esm.2013.10.001
[2]   An effective means for evaluating mixed-mode I/III stress intensity factors using single-edge notch beam specimen [J].
Ahmadi-Moghadam, Babak ;
Taheri, Farid .
JOURNAL OF STRAIN ANALYSIS FOR ENGINEERING DESIGN, 2013, 48 (04) :245-257
[3]   Mode I and mode II fracture toughness testing for a coarse grain marble [J].
Aliha, M. R. M. ;
Ashtari, R. ;
Ayatollahi, M. R. .
MODERN PRACTICE IN STRESS AND VIBRATION ANALYSIS VI, PROCEEDINGS, 2006, 5-6 :181-+
[4]   Fracture Assessment of Polymethyl Methacrylate Using Sharp Notched Disc Bend Specimens under Mixed Mode I plus III Loading [J].
Aliha, M. R. M. ;
Berto, F. ;
Bahmani, A. ;
Akhondi, Sh. ;
Barnoush, A. .
PHYSICAL MESOMECHANICS, 2016, 19 (04) :355-364
[5]   A novel test specimen for investigating the mixed mode I plus III fracture toughness of hot mix asphalt composites - Experimental and theoretical study [J].
Aliha, M. R. M. ;
Bahmani, A. ;
Akhondi, Sh. .
INTERNATIONAL JOURNAL OF SOLIDS AND STRUCTURES, 2016, 90 :167-177
[6]   Mixed mode fracture toughness testing of PMMA with different three-point bend type specimens [J].
Aliha, M. R. M. ;
Bahmani, A. ;
Akhondi, Sh. .
EUROPEAN JOURNAL OF MECHANICS A-SOLIDS, 2016, 58 :148-162
[7]   Determination of mode III fracture toughness for different materials using a new designed test configuration [J].
Aliha, M. R. M. ;
Bahmani, A. ;
Akhondi, Sh. .
MATERIALS & DESIGN, 2015, 86 :863-871
[8]   Numerical analysis of a new mixed mode I/III fracture test specimen [J].
Aliha, M. R. M. ;
Bahmani, A. ;
Akhondi, Sh. .
ENGINEERING FRACTURE MECHANICS, 2015, 134 :95-110
[9]   Rock fracture toughness study using cracked chevron notched Brazilian disc specimen under pure modes I and II loading - A statistical approach [J].
Aliha, M. R. M. ;
Ayatollahi, M. R. .
THEORETICAL AND APPLIED FRACTURE MECHANICS, 2014, 69 :17-25
[10]   Application of Cracked Triangular Specimen Subjected to Three-Point Bending for Investigating Fracture Behavior of Rock Materials [J].
Aliha, M. R. M. ;
Hosseinpour, Gh R. ;
Ayatollahi, M. R. .
ROCK MECHANICS AND ROCK ENGINEERING, 2013, 46 (05) :1023-1034