Microstructure and technology research of in-situ synthesis TiN-TiB2/Ni Composite Coating by argon arc cladding

被引：24

作者：

Meng, Junsheng ^{[1
]}

Ji, Zesheng ^{[1
]}

机构：

[1] Harbin Univ Sci & Technol, Sch Mat Sci & Engn, Harbin 150040, Peoples R China

来源：

INTERNATIONAL FEDERATION FOR HEAT TREATMENT AND SURFACE ENGINEERING (20TH CONGRESS) | 2013年 / 50卷

关键词：

argon arc cladding; In situ synthesis; TiN-TiB2; microstructure; wear; TENSILE;

D O I：

10.1016/j.phpro.2013.11.040

中图分类号：

O414.1 [热力学];

学科分类号：

摘要：

An in situ synthesis method was developed to produce an Ni alloy composite coating reinforced by in situ reacted TiN and TiB2 particles, using argon arc cladding (AAC) with different mass fractions of Ni60 and Ti+BN powders on a 16Mn steel substrate. The microstructure, micro-hardness and wear resistance were investigated using SEM, XRD, Micro-hardness Tester, and Friction and Wear Tester, respectively. The result showed that the main phases of coating were TiN TiB2 (Fe,Cr)23C6 and gamma -Ni. Excellent bonding between the coating and the 16Mn steel substrate is uniform, continuous and almost defect-free and the particles were gradient distributed in the clad coating. The microstructure is different from the outside to the inside in the clad coating. The microhardness showed a gradient variation, with the highest value of 1400HV0.2 and the wear properties of the coating are also improved at the room temperature under normal atmosphere conditions. (C) 2013 The Authors. Published by Elsevier B.V. Open access under CC BY-NC-ND license.

引用

页码：253 / 260

页数：8

共 20 条

[11] Property distribution on three-dimensionally shaped PVD-coated samples [J].

Rother, B ;

Kappl, H ;

Pfeifer-Schaller, I ;

Ebersbach, G ;

Jehn, HA .

SURFACE & COATINGS TECHNOLOGY, 1997, 97 (1-3) :200-205

[12] Characterisation of in situ Al-TiB2 nanocomposite powder synthesised by mechanical alloying [J].

Sadeghian, Z. ;

Enayati, M. H. ;

Beiss, P. .

POWDER METALLURGY, 2011, 54 (01) :46-49

[13] Microstructural and mechanical characteristics of in situ metal matrix composites [J].

Tjong, SC ;

Ma, ZY .

MATERIALS SCIENCE & ENGINEERING R-REPORTS, 2000, 29 (3-4) :49-113

[14] Production of TiB2-TiN composites by combustion synthesis and their properties [J].

Tomoshige, R ;

Murayama, A ;

Matsushita, T .

JOURNAL OF THE AMERICAN CERAMIC SOCIETY, 1997, 80 (03) :761-764

[15]

Van der Geer J., 2000, J Sci Commun, V163, P51, DOI 10.1016/j.Sc.2010.00372

[16] Reaction sintering of TiN-TiB2 ceramics [J].

Wang, K ;

Krstic, VD .

ACTA MATERIALIA, 2003, 51 (06) :1809-1819

[17] Fabricating TiC particles reinforced Fe-based composite coatings produced by GTAW multi-layers melting process [J].

Wang, X. H. ;

Song, S. L. ;

Zou, Z. D. ;

Qu, S. Y. .

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2006, 441 (1-2) :60-67

[18] Microstructure and wear properties of in situ TiC/FeCrBSi composite coating prepared by gas tungsten arc welding [J].

Wang, XH ;

Zou, ZD ;

Song, S ;

Qu, SY .

WEAR, 2006, 260 (7-8) :705-710

[19] EFFECT OF BN/Ti RATIO ON THE REACTION SYNTHESIS OF TiB2-TiNx CERAMICS [J].

Zhan, Lei ;

Shen, Ping ;

Jiang, Qi Chuan .

INTERNATIONAL JOURNAL OF MODERN PHYSICS B, 2009, 23 (6-7) :1172-1178

[20] Boron carbide and nitride as reactants for in situ synthesis of boride-containing ceramic composites [J].

Zhang, GJ ;

Ando, M ;

Yang, JF ;

Ohji, T ;

Kanzaki, S .

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY, 2004, 24 (02) :171-178

← 1 2 →