Improvement of Percussion Welding Characteristics of CuCr25 Contact Material by Decreasing Tensile Strength

被引：0

作者：

Yu, Li ^{[1
]}

Geng, Yingsan ^{[1
]}

Li, Qian ^{[1
]}

Wang, Jianhua ^{[1
]}

Liu, Zhiyuan ^{[1
]}

Li, Dongwei ^{[1
]}

Wang, Wenbin ^{[2
]}

Wang, Xiaojun ^{[2
]}

机构：

[1] Xi An Jiao Tong Univ, State Key Lab Elect Insulat & Power Equipment, Xian 710049, Peoples R China

[2] ShaanXi Sirui Ind Co LTD, Xian 710049, Peoples R China

来源：

PROCEEDINGS OF THE FIFTY-FIFTH IEEE HOLM CONFERENCE ON ELECTRICAL CONTACTS | 2009年

关键词：

percussion weld; tensile strength; contact materials; vacuum interrupters; HIGH-POWER; VACUUM;

D O I：

暂无

中图分类号：

TM [电工技术]; TN [电子技术、通信技术];

学科分类号：

0808 ; 0809 ;

摘要：

Copper-Chromium contact material is widely used in vacuum interrupters. However, there are occasionally percussion welding phenomena when CuCr25 (25% weight Cr) contact material close electrical circuit, especially in the case of high rated short circuit making current tests. It was reported that the resistance welding performance of Cu Cr contact material can be improved by adding 0.1%similar to 4"/0 Te to decrease the tensile strength. In order to investigate the influence of tensile strength of contact material on percussion welding performance by adding Te (0.01%), a percussion welding experiment was designed to compare weld force between CuCr25 and CuCr25-Te contact material. The percussion welding experiment simulated the contacts in a vacuum interrupter closed a DC circuit and bounced once. The DC currents were 300A and 400A. The bounce times were 2s and 3s. With a lower tensile strength (220 similar to 240Mpa) than CuCr25 (335 similar to 345Mpa), the CuCr25-Te contact material was less proned to occur percussion weld than CuCr25 contact material. And the maximum percussion weld forces of CuCr25-Te were also lower than CuCr25 under same arcing currents and arcing times. The percussion welding characteristic of CuCr25 contact material is proved to be superior by reducing its tensile strength.

引用

页码：195 / +

页数：3

共 14 条

[1] INSULATION CHARACTERISTICS AND WELDING BEHAVIOR OF VACUUM SWITCH CONTACTS MADE FROM VARIOUS CUCR ALLOYS
BALLAT, J
KONIG, D
[J]. IEEE TRANSACTIONS ON ELECTRICAL INSULATION, 1993, 28 (04): : 628 - 634
[2] Filip G., 1986, Proceedings of the XIIth International Symposium on Discharges and Electrical Insulation in Vacuum (Cat. No. 86CH2194-9), P224
[3] FU SJ, 1997, HIGH VOLTAGE APPARAT, V33, P16
[4] EFFECT OF CONTACT MATERIAL ON THE EXTINCTION OF VACUUM ARCS UNDER LINE FREQUENCY AND HIGH-FREQUENCY CONDITIONS
HEYN, D
LINDMAYER, M
WILKENING, ED
[J]. IEEE TRANSACTIONS ON COMPONENTS HYBRIDS AND MANUFACTURING TECHNOLOGY, 1991, 14 (01): : 65 - 70
[5] HUSLER H, 1980, P 10 INT C EL CONT B, P219
[6] ARCING AT ELECTRICAL CONTACTS ON CLOSURE .5. THE CATHODE MECHANISM OF EXTREMELY SHORT ARCS
KISLIUK, P
[J]. JOURNAL OF APPLIED PHYSICS, 1954, 25 (07) : 897 - 900
[7] KOREN PP, 1980, IEEE T COMPON HYBR, V3, P50, DOI 10.1109/TCHMT.1980.1135580
[8] Li WP, 2001, IEEE T PLASMA SCI, V29, P744, DOI 10.1109/27.964467
[9] Ozawa K., 1986, P INT C EL CONT EL C, P823
[10] Slade P. G., 2008, VACUUM INTERRUPTER T, P304

← 1 2 →