Design and Performance of Slurry Erosion Tester

被引：36

作者：

Abouel-Kasem, A. ^{[1
]}

Abd-elrhman, Y. M. ^{[1
]}

Emara, K. M. ^{[1
]}

Ahmed, S. M. ^{[1
]}

机构：

[1] Assiut Univ, Fac Engn, Dept Mech Engn, Assiut 71516, Egypt

来源：

JOURNAL OF TRIBOLOGY-TRANSACTIONS OF THE ASME | 2010年 / 132卷 / 02期

关键词：

slurry erosion; erodent-target dynamics; painting; erosion patterns; particles rebound effect; WEAR; MECHANISMS; CORROSION; BEHAVIOR; COATINGS; VELOCITY; ANGLE;

D O I：

10.1115/1.4001449

中图分类号：

TH [机械、仪表工业];

学科分类号：

0802 ;

摘要：

A slurry whirling arm erosion test ring was constructed and a series of erosion tests and post-erosion analysis were carried out using a paint erosion indication technique. The pattern of the paint removal presented a highly visual and accelerated map for the erosion process and its behavior. Also, the erosion rate of paint removal was investigated under a number of erosion variables. It was observed that the rebounding of the erodent particles from the sample surface play an important role in developing erosion for this tester. The erosion pattern showed that the effect of the rebound particles depends on the impact velocity and impingement angle. It was also observed that the erosion behavior of paint as a function of impingement angle, impact velocity, and erosion time was similar to that reported in literature for engineering materials. The slurry whirling arm erosion tester seems to be promising for simulating the slurry process in real cases. [DOI: 10.1115/1.4001449]

引用

页码：1 / 10

页数：10

共 33 条

[11] Erosion of ceramic materials by a sand/water slurry jet [J].

Fang, Q ;

Xu, H ;

Sidky, PS ;

Hocking, MG .

WEAR, 1999, 224 (02) :183-193

[12]

Finnie I., 1960, Wear, V3, P87, DOI [10.1016/00431648(60)90055-7, DOI 10.1016/0043-1648(60)90055-7]

[13] PREDICTION OF UNEVEN WEAR IN A SLURRY PIPELINE ON THE BASIS OF MEASUREMENTS IN A POT TESTER [J].

GUPTA, R ;

SINGH, SN ;

SEHADRI, V .

WEAR, 1995, 184 (02) :169-178

[14]

Hojo H., 1980, Journal of the Society of Materials Science, Japan, V29, P731, DOI 10.2472/jsms.29.731

[15]

Hutchings I.M., 1992, FRICTION WEAR ENG MA

[16] Slurry wear properties of pump lining materials [J].

Iwai, Y ;

Nambu, K .

WEAR, 1997, 210 (1-2) :211-219

[17] MICROSTRUCTURAL INFLUENCE IN SLURRY EROSION OF CERAMICS [J].

LATHABAI, S ;

PENDER, DC .

WEAR, 1995, 189 (1-2) :122-135

[18] THE INFLUENCE OF CORROSION ON THE EROSION OF ALUMINUM BY AQUEOUS SILICA SLURRIES [J].

LI, Y ;

BURSTEIN, GT ;

HUTCHINGS, IM .

WEAR, 1995, 186 (02) :515-522

[19] EFFECT OF IMPACT VELOCITY ON SLURRY EROSION AND A NEW DESIGN OF A SLURRY EROSION TESTER [J].

LIN, FY ;

SHAO, HS .

WEAR, 1991, 143 (02) :231-240

[20]

MADSEN BW, 1987, ASTM SPEC TECH PUBL, V946, P169

← 1 2 3 4 →