Microstructural and mechanical characteristics of recycled hard metals for cutting tools

被引：11
|
作者：
Faga, M. G. [2 ]
Mattioda, R. [3 ]
Settineri, L. [1 ]
机构：
[1] Politecn Torino, Dept Prod Syst & Business Econ, I-10129 Turin, Italy
[2] CNR, Inst Sci & Technol Ceram, I-10135 Turin, Italy
[3] Wolframcarb, I-10081 Castellamonte, TO, Italy
来源：
CIRP ANNALS-MANUFACTURING TECHNOLOGY | 2010年 / 59卷 / 01期
关键词：
Cutting tool; Carbide; Recycling; CEMENTED CARBIDE TOOLS; OXIDATION; DRY;
D O I：
10.1016/j.cirp.2010.03.052
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
WC-Co-based materials are widely used for cutting tools, however, powders for the materials preparation are rare and research is addressed to recycle worn materials. This paper presents a comparison between recycled and traditionally prepared WC-Co-based materials for cutting tools. Evaluation of efficiency in turning with application to 100Cr6. AISI 304 and Inconel 718 was considered, using uncoated and PACVD coated tools. Results show that carbides produced via recycling presented some residual porosity and larger grain size distribution, with different performance in cutting. Coating minimises the differences in performance between recycled and traditional hard metal tools. (C) 2010 CIRP.
引用
收藏
页码：133 / 136
页数：4
相关论文
共 50 条
  • [41] Effect of surface finishing such as sand-blasting and CrAlN hard coatings on the cutting edge's peeling tools' wear resistance
    Nouveau, C.
    Labidi, C.
    Collet, R.
    Benlatreche, Y.
    Djouadi, M. -A.
    WEAR, 2009, 267 (5-8) : 1062 - 1067
  • [42] Tool wear characteristics analysis of cBN cutting tools in high-speed turning of Inconel 718
    Tu, Luqiang
    Lin, Liangliang
    Liu, Chao
    Zheng, Tianchang
    Deng, Yadi
    Han, Lei
    An, Qinglong
    Ming, Weiwei
    Chen, Ming
    CERAMICS INTERNATIONAL, 2023, 49 (01) : 635 - 658
  • [43] Influence of fine recycled concrete aggregates use on the hydration kinetics and mechanical-microstructural properties of hydrated cement: Experimental and numerical approaches
    Abriak, Yassine
    Chu, Duc Chinh
    Maherzi, Walid
    Benzerzour, Mahfoud
    Rivard, Patrice
    CONSTRUCTION AND BUILDING MATERIALS, 2023, 408
  • [44] Effect of GBFS ratio and recycled steel tire wire on the mechanical and microstructural properties of geopolymer concrete under ambient and oven curing conditions
    Celik, Ali Ihsan
    Karalar, Memduh
    Aksoylu, Ceyhun
    Mydin, Md Azree Othuman
    Althaqafi, Essam
    Yilmaz, Fatih
    Umiye, Osman Ahmed
    Ozkilic, Yasin Onuralp
    CASE STUDIES IN CONSTRUCTION MATERIALS, 2024, 21
  • [45] Assessment of tool wear and microstructural alteration of the cutting tools in conventional and sustainable slot milling of Ti-6Al-4V alloy
    Khatri, Ashutosh
    Jahan, Muhammd P.
    Ma, Jianfeng
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2019, 105 (7-8) : 2799 - 2814
  • [46] Effects of Working Parameters on Performance Characteristics of Cutting Tools Processed through Powder Metallurgy under Turning Operation
    T. Panneerselvam
    T. K. Kandavel
    S. Aravinda Sreenivas
    S. Karthik
    M. Marshal Andru
    Journal of Materials Engineering and Performance, 2021, 30 : 2890 - 2898
  • [47] Effects of Working Parameters on Performance Characteristics of Cutting Tools Processed through Powder Metallurgy under Turning Operation
    Panneerselvam, T.
    Kandavel, T. K.
    Sreenivas, S. Aravinda
    Karthik, S.
    Andru, M. Marshal
    JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE, 2021, 30 (04) : 2890 - 2898
  • [48] Microstructure and mechanical properties of titanium nitride coatings for cemented carbide cutting tools by pulsed high energy density plasma
    Peng, ZJ
    Miao, HH
    Qi, LH
    Gong, JH
    Yang, S
    Liu, CZ
    CHINESE SCIENCE BULLETIN, 2003, 48 (13): : 1316 - 1320
  • [49] Microstructure and mechanical properties of titanium nitride coatings for cemented carbide cutting tools by pulsed high energy density plasma
    PENG Zhijian1
    2. Institute of Physics
    ChineseScienceBulletin, 2003, (13) : 1316 - 1320
  • [50] Role of nano-WC addition on microstructural, mechanical and thermal characteristics of TiC-SiCw composite
    Fattahi, Mehdi
    Asl, Mehdi Shahedi
    Delbari, Seyed Ali
    Namini, Abbas Sabahi
    Ahmadi, Zohre
    Mohammadi, Mohsen
    INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS, 2020, 90
12345