Microstructural and mechanical characteristics of recycled hard metals for cutting tools

被引：11
|
作者：
Faga, M. G. [2 ]
Mattioda, R. [3 ]
Settineri, L. [1 ]
机构：
[1] Politecn Torino, Dept Prod Syst & Business Econ, I-10129 Turin, Italy
[2] CNR, Inst Sci & Technol Ceram, I-10135 Turin, Italy
[3] Wolframcarb, I-10081 Castellamonte, TO, Italy
来源：
CIRP ANNALS-MANUFACTURING TECHNOLOGY | 2010年 / 59卷 / 01期
关键词：
Cutting tool; Carbide; Recycling; CEMENTED CARBIDE TOOLS; OXIDATION; DRY;
D O I：
10.1016/j.cirp.2010.03.052
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
WC-Co-based materials are widely used for cutting tools, however, powders for the materials preparation are rare and research is addressed to recycle worn materials. This paper presents a comparison between recycled and traditionally prepared WC-Co-based materials for cutting tools. Evaluation of efficiency in turning with application to 100Cr6. AISI 304 and Inconel 718 was considered, using uncoated and PACVD coated tools. Results show that carbides produced via recycling presented some residual porosity and larger grain size distribution, with different performance in cutting. Coating minimises the differences in performance between recycled and traditional hard metal tools. (C) 2010 CIRP.
引用
收藏
页码：133 / 136
页数：4
相关论文
共 50 条
  • [21] Wear characteristics of polycrystalline diamond tools in orthogonal cutting of CFRP/Ti stacks
    Xu, Jinyang
    El Mansori, Mohamed
    WEAR, 2017, 376 : 91 - 106
  • [22] Mechanical and tribological characterization of TiAlN/TiN and TiSiN/AlTiN coating systems for cutting tools
    Alves, Ueliton C.
    Ricci, Virgilio P.
    Mota, Igor G. C.
    Koga, Guilherme Y.
    Hassui, Amauri
    Ventura, Carlos E. H.
    JOURNAL OF MANUFACTURING PROCESSES, 2025, 145 : 522 - 535
  • [23] Microstructural characteristics and mechanical properties of HVOF sprayed NiCrAl coating on superalloys
    Mahesh, R. A.
    Jayaganthan, R.
    Prakash, S.
    JOURNAL OF ALLOYS AND COMPOUNDS, 2009, 468 (1-2) : 392 - 405
  • [24] Effect of Red Mud on Mechanical and Microstructural Characteristics of Aluminum Matrix Composites
    Samal, Priyaranjan
    Raj, Rishu
    Mandava, Ravi Kumar
    Vundavilli, Pandu R.
    ADVANCES IN MATERIALS AND MANUFACTURING ENGINEERING, ICAMME 2019, 2020, : 75 - 82
  • [25] Mechanical and cutting performance of cemented carbide tools with Cr/x/DLC composite coatings
    Hao, Tianmei
    Du, Jin
    Su, Guosheng
    Zhang, Peirong
    Sun, Yujing
    Zhang, Jingjie
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2020, 106 (11-12) : 5241 - 5254
  • [26] Analysis of the Surface Quality Characteristics in Hard Turning Under a Minimal Cutting Fluid Environment
    Mane, Sandip
    Patil, Rajkumar Bhimgonda
    Roy, Anindita
    Shah, Pritesh
    Sekhar, Ravi
    APPLIED MECHANICS, 2025, 6 (01):
  • [27] Influence of short and long term aging on chemical, microstructural and macro-mechanical properties of recycled asphalt mixtures
    Poulikakos, Lily D.
    dos Santos, Salome
    Bueno, Moises
    Kuentzel, Simon
    Hugener, Martin
    Partl, Manfred N.
    CONSTRUCTION AND BUILDING MATERIALS, 2014, 51 : 414 - 423
  • [28] Cutting characteristics of PVD-coated tools deposited by Unbalanced Magnetron Sputtering method
    Hosokawa, Akira
    Shimamura, Koji
    Ueda, Takashi
    CIRP ANNALS-MANUFACTURING TECHNOLOGY, 2012, 61 (01) : 95 - 98
  • [29] Recovery of critical and strategic metals from scrap marble-cutting tools by oxidative leaching and precipitation
    Celep, Oktay
    Ahlatci, Firat
    Yazici, Ersin Yener
    Deveci, Haci
    SEPARATION AND PURIFICATION TECHNOLOGY, 2024, 338
  • [30] High-temperature mechanical properties of WC-Co hard metals (Review)
    N. V. Novikov
    V. P. Bondarenko
    V. T. Golovchan
    Journal of Superhard Materials, 2007, 29 (5) : 261 - 280
12345