Improvement of Corrosion Resistance of Maraging Steel Manufactured by Selective Laser Melting Through Intercritical Heat Treatment

被引:8
作者
Khan, Hamaid Mahmood [1 ]
Ozer, Gokhan [1 ]
Yilmaz, Mustafa Safa [1 ]
Tarakci, Gurkan [1 ]
机构
[1] Fatih Sultan Mehmet Vakif Univ, ALUTEAM, Halic Campus, TR-34445 Istanbul, Turkey
关键词
  additive manufacturing; austenite reversion; corrosion; maraging steel; selective laser melting; 316L STAINLESS-STEEL; MECHANICAL-PROPERTIES; AUSTENITE REVERSION; PITTING CORROSION; MICROSTRUCTURAL EVOLUTION; BEHAVIOR; IMPACT; PRECIPITATION; COMPONENTS; STABILITY;
D O I
10.5006/3972
中图分类号
T [工业技术];
学科分类号
08 ;
摘要
Selective laser melting allows the layerwise fabrication of bespoke designs, creating new prospects in applications and properties compared to conventional methods. Like other ultra-high-strength steels, maraging steels offer a high toughness/strength ratio. However, additively prepared maraging steels??? lower ductility and strain-hardening limit their commercial adaptability. Studies exist that show superior mechanical performance is attainable through martensite-to-austenite reversion. However, their impact on corrosion properties is not well understood. In the present study, maraging steel specimens were tempered close to austenite forming temperatures to investigate the reversed austenite effect on maraging steels??? pitting behavior. X-ray diffraction, scanning electron microscopy, and energy-dispersive x-ray spectroscopy were used to characterize selective laser melting samples??? microstructure. To characterize and analyze the pitting performance, potentiodynamic polarization and open-circuit potential were performed in a 3.5 wt% NaCl solution. The intercritical heattreatment within ????? + ?? range of 720??C shows that reversed austenite precipitated mainly along the martensite laths boundaries. The local Ni enrichment as a result of intermetallic particles??? dissolution enables the nucleation of reversed austenite. As a result, the 720??C-tempered specimen exhibits a higher pitting potential, lower corrosion current density, and lower corrosion rate than the as-printed, aged, and homogenized (without reversed austenite) specimens. This study shows that the reversed austenite enhances the pitting resistance of maraging steels.
引用
收藏
页码:239 / 248
页数:10
相关论文
共 73 条
[1]   Corrosion behavior and biocompatibility of additively manufactured 316L stainless steel in a physiological environment: the effect of citrate ions [J].
Al-Mamun, Nahid Sultan ;
Deen, Kashif Mairaj ;
Haider, Waseem ;
Asselin, Edouard ;
Shabib, Ishraq .
ADDITIVE MANUFACTURING, 2020, 34
[2]   A critical review on susceptibility of stress corrosion cracking in maraging steel weldments [J].
Bagchi, Arghya ;
Gope, Deepak Kumar ;
Chattopadhyaya, S. ;
Wuriti, Gowrishankar .
MATERIALS TODAY-PROCEEDINGS, 2020, 27 :2303-2307
[3]   Steels in additive manufacturing: A review of their microstructure and properties [J].
Bajaj, P. ;
Hariharan, A. ;
Kini, A. ;
Kuernsteiner, P. ;
Raabe, D. ;
Jaegle, E. A. .
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2020, 772
[4]   The achievable mechanical properties of SLM produced Maraging Steel 300 components [J].
Becker, Thorsten Hermann ;
Dimitrov, Dimitri .
RAPID PROTOTYPING JOURNAL, 2016, 22 (03) :487-494
[5]   Correlation between microstructure and intergranular corrosion behavior of low delta-ferrite content AISI 316L aged in the range 550-700 °C [J].
Ben Rhouma, A. ;
Amadou, T. ;
Sidhom, H. ;
Braham, C. .
JOURNAL OF ALLOYS AND COMPOUNDS, 2017, 708 :871-886
[6]   Evaluation of corrosion resistance of Al-10Si-Mg alloy obtained by means of Direct Metal Laser Sintering [J].
Cabrini, Marina ;
Lorenzi, Sergio ;
Pastore, Tommaso ;
Pellegrini, Simone ;
Manfredi, Diego ;
Fino, Paolo ;
Biamino, Sara ;
Badini, Claudio .
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2016, 231 :326-335
[7]   Aging Behaviour and Mechanical Performance of 18-Ni 300 Steel Processed by Selective Laser Melting [J].
Casati, Riccardo ;
Lemke, Jannis N. ;
Tuissi, Ausonio ;
Vedani, Maurizio .
METALS, 2016, 6 (09)
[8]   On the enhanced corrosion resistance of a selective laser melted austenitic stainless steel [J].
Chao, Qi ;
Cruz, Victor ;
Thomas, Sebastian ;
Birbilis, Nick ;
Collins, Paul ;
Taylor, Adam ;
Hodgson, Peter D. ;
Fabijanic, Daniel .
SCRIPTA MATERIALIA, 2017, 141 :94-98
[9]   Effect of thermal cycling and aging stages on the microstructure and bending strength of a selective laser melted 300-grade maraging steel [J].
Conde, F. F. ;
Escobar, J. D. ;
Oliveira, J. P. ;
Beres, M. ;
Jardini, A. L. ;
Bose, W. W. ;
Avila, J. A. .
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2019, 758 :192-201
[10]   Additive manufacturing of metallic components - Process, structure and properties [J].
DebRoy, T. ;
Wei, H. L. ;
Zuback, J. S. ;
Mukherjee, T. ;
Elmer, J. W. ;
Milewski, J. O. ;
Beese, A. M. ;
Wilson-Heid, A. ;
De, A. ;
Zhang, W. .
PROGRESS IN MATERIALS SCIENCE, 2018, 92 :112-224