Analytical and experimental investigations of crack propagation in adhesively bonded joints with the Mixed Mode Bending (MMB) test Part II: Investigation of cohesive stresses distribution with backface strain monitoring

被引：8
作者：
Ben Salem, N. [1 ,2 ,3 ,4 ]
Jumel, J. [1 ,2 ,3 ]
Budzik, M. K. [1 ,2 ,3 ,4 ]
Shanahan, M. E. R. [1 ,2 ,3 ]
Lavelle, F. [4 ]
机构：
[1] Univ Bordeaux, I2M, UMR 5295, F-33400 Talence, France
[2] CNRS, I2M, UMR 5295, F-33400 Talence, France
[3] CNRS, I2M, Arts & Met ParisTech, F-33400 Talence, France
[4] French Space Agcy CNES DLA, F-75612 Paris, France
来源：
THEORETICAL AND APPLIED FRACTURE MECHANICS | 2014年 / 74卷
关键词：
Bonded joint; Mixed mode bending test; Crack propagation; Cohesive stress; Backface strain monitoring; END NOTCHED FLEXURE; PROCESS ZONE; CANTILEVER BEAM; DELAMINATION; FRACTURE; FAILURE; LAWS; SIMULATION; TOUGHNESS; STRENGTH;
D O I：
10.1016/j.tafmec.2014.05.007
中图分类号：
TH [机械、仪表工业];
学科分类号：
0802 ;
摘要：
Backface strain monitoring is used for probing the peel and shear cohesive stresses distribution along an adhesive layer during a crack propagation test under mixed mode conditions. An elastic model consisting of two Timoshenko beams attached with an elastic layer is derived to obtain simple analytical estimate of the specimen deformation from which a simple data reduction procedure is proposed. Taking benefit of the specimen symmetry, a proper experimental arrangement allows to separate the mode I and mode II contributions. Such protocol is less affected by the experimental artifacts which are observed on classical force versus displacement measurements from which are based the traditional fracture mechanics data reduction protocols. Additionally, backface strain measurements show superior sensitivity to non-linear interface behavior which should improve the quality of cohesive zone models identification. (C) 2014 Elsevier Ltd. All rights reserved.
引用
收藏
页码：222 / 232
页数：11
相关论文
共 49 条
[1]   On the influence of the shape of the interface law on the application of cohesive-zone models [J].
Alfano, G .
COMPOSITES SCIENCE AND TECHNOLOGY, 2006, 66 (06) :723-730
[2]   On the instantaneous energy release rate of the end-notch flexure adhesive joint specimen [J].
Alfredsson, KS .
INTERNATIONAL JOURNAL OF SOLIDS AND STRUCTURES, 2004, 41 (16-17) :4787-4807
[3]  
Anthony J., 1988, INT J FRACTURE, V38, P19
[4]   Representativity of the singular stress state in the failure of adhesively bonded joints between metals and composites [J].
Barroso, A. ;
Paris, F. ;
Mantic, V. .
COMPOSITES SCIENCE AND TECHNOLOGY, 2009, 69 (11-12) :1746-1755
[5]   Investigation of the crack front process zone in the Double Cantilever Beam test with backface strain monitoring technique [J].
Ben Salem, N. ;
Budzik, M. K. ;
Jumel, J. ;
Shanahan, M. E. R. ;
Lavelle, F. .
ENGINEERING FRACTURE MECHANICS, 2013, 98 :272-283
[6]  
Ben Salem N., 2013, J ADHES SCI TECHNOL, P1
[7]  
Bennati S., 2013, MECCANICA, P1
[8]   Effect of Adhesive Compliance in the Assessment of Soft Adhesives with the Wedge Test [J].
Budzik, M. ;
Jumel, J. ;
Imielinska, K. ;
Shanahan, M. E. R. .
JOURNAL OF ADHESION SCIENCE AND TECHNOLOGY, 2011, 25 (1-3) :131-149
[9]   Instrumented end notched flexure - Crack propagation and process zone monitoring Part II: Data reduction and experimental [J].
Budzik, M. K. ;
Jumel, J. ;
Ben Salem, N. ;
Shanahan, M. E. R. .
INTERNATIONAL JOURNAL OF SOLIDS AND STRUCTURES, 2013, 50 (02) :310-319
[10]   Process zone in the Single Cantilever Beam under transverse loading - Part II: Experimental [J].
Budzik, M. K. ;
Jumel, J. ;
Shanahan, M. E. R. .
THEORETICAL AND APPLIED FRACTURE MECHANICS, 2011, 56 (01) :13-21
12345