Properties of Carbon Fibers after Applying Metal Coatings on them by Magnetron Sputtering Technology

被引：6

作者：

Nelyub, V. A. ^{[1
]}

Fedorov, S. Yu ^{[1
]}

Malysheva, G., V ^{[1
]}

Berlin, A. A. ^{[2
]}

机构：

[1] Bauman Moscow State Tech Univ BMSTU, Moscow, Russia

[2] RAS, NN Semenov Inst Chem Phys, St Petersburg, Russia

来源：

FIBRE CHEMISTRY | 2021年 / 53卷 / 04期

关键词：

16;

D O I：

10.1007/s10692-022-10279-5

中图分类号：

O6 [化学];

学科分类号：

0703 ;

摘要：

Using magnetron sputtering technology, two types of metal coatings, stainless steel and titanium, are applied to the surface of unidirectional carbon tape. Prior to the deposition of metal coatings, the surface of the carbon tape was pretreated in a low-temperature plasma in air. The results of the adhesion strength of the metal coatings to the carbon surface and the structural analysis of elementary carbon fibers with metal coatings are presented, and their thicknesses are determined. It was found that the adhesion strength of the metal coating to the carbon tape after its activation by low-temperature plasma increases. Samples of carbon plastics were made using vacuum infusion technology and it was found that their strength at interlayer shear, when using metallized carbon tape, increases by 10-40%.

引用

页码：252 / 257

页数：6

共 16 条

[1] ACCURACY OF DIAGNOSIS OF METAL STRUCTURES USING CARBON FIBERS
Baurova, N. I.
Zorin, V. A.
Prikhod'ko, V. M.
[J]. FIBRE CHEMISTRY, 2017, 48 (06) : 504 - 506
[2] Influence of Structural Defects in Carbon Fibers on Their Sensor Properties Evaluated Using Scanning Electron Microscopy
Baurova, N. I.
Zorin, V. A.
Prikhod'ko, V. M.
[J]. FIBRE CHEMISTRY, 2015, 46 (05) : 283 - 287
[3] Providing dismountable rivet bonded joints through the use of hot-melt adhesives
Baurova, Natalia
Anoprienko, Alexander
Romanova, Yulia
[J]. INTERNATIONAL CONFERENCE ON MODERN TRENDS IN MANUFACTURING TECHNOLOGIES AND EQUIPMENT (ICMTMTE 2017), 2017, 129
[4] Baurova NI., 2016, CHEM ENG-NEW YORK, V50, P119
[5] Baurova NI., 2016, USE POLYM COMPOSITE, P264
[6] Bazhenov S. L., 2010, POLYM COMPOSITE MAT
[7] Simulation of impregnation kinetics of fabric fillers in the production of fiberglass articles
Borodulin, A. S.
Marycheva, A. N.
Malysheva, G. V.
[J]. GLASS PHYSICS AND CHEMISTRY, 2015, 41 (06) : 660 - 664
[8] Technology of Forming and the Properties of Reinforced Composites Based on an Inorganic Binder
Gorodetskii, M. A.
Nelyub, V. A.
Malysheva, G. V.
Shaulov, A. Yu.
Berlin, A. A.
[J]. RUSSIAN METALLURGY, 2018, (13): : 1195 - 1198
[9] [Кондрашов С.В. Kondrashov S.V.], 2016, [Труды ВИАМ, Trudy VIAM], P7, DOI 10.18577/2307-6046-2016-0-3-7-7
[10] Hardness of the near-weld zone during contact spot welding of steels using an adhesive–weld technology
Konoplin A.Y.
Baurova N.I.
[J]. Russian Metallurgy (Metally), 2016, 2016 (13) : 1308 - 1311

← 1 2 →