Surface Evaluation of Polishing Techniques for New Resilient CAD/CAM Restorative Materials

被引:60
作者
Fasbinder, Dennis J. [1 ]
Neiva, Gisele F. [2 ]
机构
[1] Univ Michigan, Sch Dent, Dept Cariol Restorat Sci & Endodont, Ann Arbor, MI 48109 USA
[2] Univ Michigan, Sch Dent, Dept Cariol Restorat Sci & Endodont, Ann Arbor, MI 48109 USA
关键词
ROUGHNESS; PORCELAIN; PERFORMANCE; WEAR;
D O I
10.1111/jerd.12174
中图分类号
R78 [口腔科学];
学科分类号
1003 ;
摘要
Purpose: The purpose of this study was to measure the surface roughness of milled chairside computer-assisted design/computer assisted machining (CAD/CAM) restorations using several contouring/polishing systems as to their effectiveness for creating a clinically acceptable surface. Materials and Methods: One hundred onlays were milled from monolithic CAD/CAM blocks with an MCXL milling chamber (Sirona Dental) as follows: 30 resin nano-ceramic (Lava Ultimate, 3M ESPE), 30 hybrid ceramic (Enamic, Vita) and 40 leucite-reinforced ceramic (EmpressCAD, Ivoclar). A single group of EmpressCAD onlays was glazed-fired in a porcelain oven (Programat CS2, Ivoclar). Finishing and polishing systems consisted of either an abrasive-polish technique or a brush-polish technique. Roughness values were measured using a three-dimensional measuring laser microscope (OLS4000 LEXT by Olympus). Results: There was a significant difference in the baseline surface roughness of the CAD/CAM materials (p <= 0.05), with the resin nano-ceramic (Lava Ultimate) being smoother than the hybrid ceramic (Enamic), and both being smoother than the leucite-reinforced ceramic (EmpressCAD). All polishing techniques resulted in a smoother surface compared with the baseline surface for the leucite-reinforced ceramic (p <= 0.05), with both techniques resulting in a significantly smoother surface than glazing in a porcelain oven (p <= 0.05). Both polishing techniques resulted in a smoother surface compared with the baseline surface for both the nano-ceramic and hybrid ceramic materials (p <= 0.05). Conclusions: It is possible to create an equally smooth surface for chairside CAD/CAM resilient materials compared with milled ceramics using several finishing and polishing techniques. In general, the polished ceramic surfaces were smoother than the glazed ceramic surfaces.
引用
收藏
页码:56 / 66
页数:11
相关论文
共 22 条
[1]  
al-Wahadni A, 1998, J Can Dent Assoc, V64, P580
[2]   An in vitro investigation into the wear effects of glazed, unglazed and refinished dental porcelain on an opposing material [J].
Al-Wahadni, AM ;
Martin, DM .
JOURNAL OF ORAL REHABILITATION, 1999, 26 (06) :538-546
[3]   Which mechanical and physical testing methods are relevant for predicting the clinical performance of ceramic-based dental prostheses? [J].
Anusavice, K. F. ;
Kakar, Kunian ;
Ferree, N. .
CLINICAL ORAL IMPLANTS RESEARCH, 2007, 18 :218-231
[4]   STRENGTHENING OF PORCELAIN BY ION-EXCHANGE SUBSEQUENT TO THERMAL TEMPERING [J].
ANUSAVICE, KJ ;
SHEN, C ;
VERMOST, B ;
CHOW, B .
DENTAL MATERIALS, 1992, 8 (03) :149-152
[5]   Mechanical fatigue degradation of ceramics versus resin composites for dental restorations [J].
Belli, Renan ;
Geinzer, Eva ;
Muschweck, Anna ;
Petschelt, Anselm ;
Lohbauer, Ulrich .
DENTAL MATERIALS, 2014, 30 (04) :424-432
[6]  
Bottino Marco Cícero, 2006, Braz. Dent. J., V17, P285, DOI 10.1590/S0103-64402006000400004
[7]   Effects of surface finish and fatigue testing on the fracture strength of CAD-CAM and pressed-ceramic crowns [J].
Chen, HY ;
Hickel, R ;
Setcos, JC ;
Kunzelmann, KH .
JOURNAL OF PROSTHETIC DENTISTRY, 1999, 82 (04) :468-475
[8]   Effects of Six Surface Treatment Methods on the Surface Roughness of a Low-Fusing and an Ultra Low-Fusing Feldspathic Ceramic Material [J].
Dalkiz, Mehmet ;
Sipahi, Cumhur ;
Beydemir, Bedri .
JOURNAL OF PROSTHODONTICS-IMPLANT ESTHETIC AND RECONSTRUCTIVE DENTISTRY, 2009, 18 (03) :217-222
[9]   The influence of surface roughness on porcelain strength [J].
de Jager, N ;
Feilzer, AJ ;
Davidson, CL .
DENTAL MATERIALS, 2000, 16 (06) :381-388
[10]   Characterization of a polymer-infiltrated ceramic-network material [J].
Della Bona, Alvaro ;
Corazza, Pedro H. ;
Zhang, Yu .
DENTAL MATERIALS, 2014, 30 (05) :564-569