Load history effect on FCGR behaviour of 304LN stainless steel

被引：21

作者：

Biswas, Somjeet

Sivaprasad, S. ^{[1
]}

Narasaiah, N.

Tarafder, S.

Chakraborti, P. C.

机构：

[1] Natl Met Lab, Jamshedpur 831007, Bihar, India

[2] Jadavpur Univ, Kolkata 700032, W Bengal, India

来源：

INTERNATIONAL JOURNAL OF FATIGUE | 2007年 / 29卷 / 04期

关键词：

load history effect; FCGR; 304LN stainless steel; constant K-max; strain induced martensite;

D O I：

10.1016/j.ijfatigue.2006.06.003

中图分类号：

TH [机械、仪表工业];

学科分类号：

0802 ;

摘要：

FCGR behaviour of 304LN stainless steel was studied employing (i) constant R and (ii) constant K-max cyclic loading envelopes. The closure free crack growth rates obtained by the constant K-max method were always lower than that of the constant R procedure. Martensitic transformation at the crack tip was observed in both the cases. Qualitatively, the constant K-max method produced more martensite than the constant R procedure. The martensitic transformation is thought to decrease the applied stress amplitude due to volurnetric, expansion and strain associated with phase transformation. The dissimilarity in the martensitic transformation and the resultant reduction in the applied stress cycle produced by the two methods were thought to be the reasons for the observed difference in the crack growth rates. (c) 2006 Elsevier Ltd. All rights reserved.

引用

页码：786 / 791

页数：6

共 24 条

[11] Effect of carbon on the cold-worked state and annealing behavior of two 18wt%Cr-8wt%Ni austenitic stainless steels [J].

Martins, LFM ;

Plaut, RL ;

Padilha, AF .

ISIJ INTERNATIONAL, 1998, 38 (06) :572-579

[12] INFLUENCE OF DEFORMATION-INDUCED MARTENSITE ON FATIGUE CRACK-PROPAGATION IN 304-TYPE STEELS [J].

MEI, Z ;

MORRIS, JW .

METALLURGICAL TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE, 1990, 21 (12) :3137-3152

[13]

Mitra A, 2004, METALL MATER TRANS A, V35A, P599

[14] Deformation induced martensitic transformation in stainless steels [J].

Nagy, E ;

Mertinger, V ;

Tranta, F ;

Sólyom, J .

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2004, 378 (1-2) :308-313

[15]

NEWMAN JC, 1999, NASATM1999209133 LAN

[16]

Nohara K., 1977, J IRON STEEL I JPN, V63, P212

[17] Room-temperature plastic flow and strain-induced martensitic transformation in 1.2 wt% Ni metastable austenitic stainless steel sheets [J].

Raj, AK ;

Padmanabhan, KA .

JOURNAL OF MATERIALS SCIENCE LETTERS, 1997, 16 (23) :1920-1924

[18]

RAMAN SGS, 1994, J MATER SCI LETT, V13, P389, DOI 10.1007/BF00420808

[19] Crack tip driving forces and crack growth representation under fatigue [J].

Sadananda, K ;

Vasudevan, AK .

INTERNATIONAL JOURNAL OF FATIGUE, 2004, 26 (01) :39-47

[20] STACKING-FAULT ENERGIES OF 7 COMMERCIAL AUSTENITIC STAINLESS-STEELS [J].

SCHRAMM, RE ;

REED, RP .

METALLURGICAL TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE, 1975, 6 (07) :1345-1351

← 1 2 3 →